Yamaha YZF-R1 2007 Service Manual Download

Page: 340 / 442

CHARGING SYSTEM

8-13

EAS27230

TROUBLESHOOTING
The battery is not being charged.

NOTE:

• Before troubleshooting, remove the following part(s):
1 Rider seat
2 Fuel tank
3 Air filter case

→

↓

→

↓

→

↓

→

↓

→

↓

1 Check the fuse.

(Main)
Refer to "CHECKING THE FUSES"
on page 8-89.

Replace the fuse.

2 Check the battery.

Refer to "CHECKING AND
CHARGING THE BATTERY" on
page 8-89.

• Clean the battery terminals.
• Recharge or replace the battery.

3 Check the stator coil

Refer to "CHECKING THE STATOR
COIL" on page 8-97.

• Replace the stator coil assembly.

4 Check the rectifier/regulator.

Refer to "CHECKING THE RECTI-
FIER/REGULATOR" on page 8-97.

Replace the rectifier/regulator.

5 Check the entire charging system’s

wiring.
Refer to "CHARGING SYSTEM" on
page 8-11.

Properly connect or repair the charg-
ing system’s wiring.

This circuit is OK.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands