Yamaha YZF-R1 2007 Service Manual Download

Page: 154 / 442

FRONT BRAKE

4-25

EAS22220

INTRODUCTION

WARNING

EWA14100

Disc brake components rarely require dis-
assembly. Therefore, always follow these
preventive measures:
• Never disassemble brake components

unless absolutely necessary.

• If any connection on the hydraulic brake

system is disconnected, the entire brake
system must be disassembled, drained,
cleaned, properly filled, and bled after
reassembly.

• Never use solvents on internal brake

components.

• Use only clean or new brake fluid for

cleaning brake components.

• Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.

• Avoid brake fluid coming into contact

with the eyes as it can cause serious
injury.

• FIRST AID FOR BRAKE FLUID ENTERING

THE EYES:

• Flush with water for 15 minutes and get

immediate medical attention.

EAS22240

CHECKING THE FRONT BRAKE DISCS
The following procedure applies to both brake
discs.
1. Remove:

• Front wheel

Refer to "FRONT WHEEL" on page 4-8.

2. Check:

• Brake disc

Damage/galling

→

Replace.

3. Measure:

• Brake disc deflection

Out of specification

→

Correct the brake

disc deflection or replace the brake disc.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Place the vehicle on a suitable stand so

that the front wheel is elevated.

b. Before measuring the front brake disc

deflection, turn the handlebar to the left or
right to ensure that the front wheel is sta-
tionary.

c. Remove the brake caliper.
d. Hold the dial gauge at a right angle against

the brake disc surface.

e. Measure the deflection 1.5 mm (0.06 in)

below the edge of the brake disc.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Measure:

• Brake disc thickness

Measure the brake disc thickness at a few
different locations.
Out of specification

→

Replace.

5. Adjust:

• Brake disc deflection

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the brake disc.
b. Rotate the brake disc by one bolt hole.
c. Install the brake disc.

NOTE:

Tighten the brake disc bolts in stages and in a
crisscross pattern.

Brake disc deflection limit

0.10 mm (0.0039 in)

Brake disc thickness limit

4.5 mm (0.18 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands