Yamaha YZF-R1 2007 Service Manual Download

Page: 141 / 442

FRONT WHEEL

4-12

NOTE:

Start with the lightest weight.

b. Turn the front wheel 90

so that the heavy

spot is positioned as shown.

c. If the heavy spot does not stay in that posi-

tion, install a heavier weight.

d. Repeat steps (b) and (c) until the front

wheel is balanced.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

• Front wheel static balance

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the front wheel and make sure it stays

at each position shown.

b. If the front wheel does not remain station-

ary at all of the positions, rebalance it.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS22000

INSTALLING THE FRONT WHEEL
The following procedure applies to both of the
brake discs.

1. Lubricate:

• Wheel axle
• Oil seal lips

2. Lift the wheel up between the fork legs.
3. Insert the wheel axle.

NOTE:

Install the tire and wheel with the mark “1”
pointing in the direction of wheel rotation.

4. Lower the front wheel so that it is on the

ground.

5. Tighten:

• Front wheel axle bolt

• Front wheel axle pinch bolt

CAUTION:

ECA4C81001

Before tightening the wheel axle, push
down hard on the handlebar(s) several
times and check if the front fork rebounds
smoothly.

6. Install:

• Front brake calipers

WARNING

EWA13490

Make sure the brake cable is routed prop-
erly.

Recommended lubricant

Lithium-soap-based grease

Front wheel axle bolt

91 Nm (9.1 m·kg, 66 ft·lb)

Front wheel axle pinch bolt

21 Nm (2.1 m·kg, 15 ft·lb)

Front brake caliper bolt

35 Nm (3.5 m·kg, 25 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands