Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 428 / 442

background image

ELECTRICAL COMPONENTS

8-101

d. Slowly heat the coolant, and then let it cool

to the specified temperature indicated in
the table.

e. Check the coolant temperature sensor for

continuity at the temperatures indicated in
the table.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS4C81022

CHECKING THE THROTTLE POSITION
SENSOR (FOR THROTTLE CABLE PUL-
LEY)
1. Remove:

• Throttle position sensor (for throttle cable

pulley)
(from the throttle body)

2. Check:

• Throttle position sensor (for throttle cable

pulley) maximum resistance
Out of specification

→

Replace the throttle

position sensor (for throttle cable pulley)

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

Ω

×

1k) to the

throttle position sensor terminal as shown.

b. Measure the throttle position sensor (for

throttle cable pulley) maximum resistance.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Install:

• Throttle position sensor (for throttle cable

pulley)

NOTE:

When installing the throttle position sensor (for
throttle cable pulley), adjust its angle properly.
Refer to "ADJUSTING THE THROTTLE POSI-
TION SENSOR (FOR THROTTLE CABLE
PULLEY)" on page 7-7.

EAS28300

CHECKING THE THROTTLE POSITION
SENSOR (FOR THROTTLE VALVES)
1. Remove:

• Throttle position sensor (for throttle valves)

(from the throttle body)

2. Check:

• Throttle position sensor (for throttle valves)

maximum resistance
Out of specification

→

Replace the throttle

position sensor (for throttle valves)

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

Ω

×

1k) to the

throttle position sensor as shown.

b. Measure the throttle position sensor (for

throttle valves) maximum resistance.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Install:

• Throttle position sensor (for throttle valves)

Resistance

2.0–3.0 k

Ω

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester prove

→

White “1”

• Negative tester prove

→

Black “2”

Resistance

2.0–3.0 k

Ω

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester prove

→

White “1”

• Negative tester prove

→

Black “2”

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
426
427
428
429
430
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: GAS GAS Pages: 70

COMFORT 10130810

Brand: Contracor Pages: 36

Brand: hepco & becker Pages: 6

Brand: Suzuki Pages: 199

Brand: Parweld Pages: 4

Mambo Evo PURE CARBON

Brand: LAZER Pages: 13

Scorpion Exo-T520

Brand: Dennis Kirk Pages: 10

Brand: Honda Pages: 224

Brand: PUIG Pages: 2

Brand: Memphis Shades Pages: 2

Brand: DYNATEK Pages: 12

Brand: LSL Pages: 4

Brand: CyClone Pages: 24

Brand: Datatool Pages: 5

Brand: Wunderkind Custom Pages: 7

Brand: APRILIA Pages: 80

DUCATI IGCS0703

Brand: Peg-Perego Pages: 24

98-13 STREET GLIDE

Brand: Sinister Sound Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands