Yamaha YZF-R1 2007 Service Manual Download

Page: 172 / 442

REAR BRAKE

4-43

4. Check:

• Brake hoses “1”

Cracks/damage/wear

→

Replace.

EAS22730

ASSEMBLING THE REAR BRAKE MASTER
CYLINDER

WARNING

EWA13520

• Before installation, all internal brake com-

ponents should be cleaned and lubricated
with clean or new brake fluid.

• Never use solvents on internal brake

components.

1. Instal:

• Brake master cylinder kit

EAS22740

INSTALLING THE REAR BRAKE MASTER
CYLINDER
1. Install:

• Copper washers
• Brake hoses
• Union bolt

WARNING

EWA13530

Proper brake hose routing is essential to
insure safe vehicle operation. Refer to
"CABLE ROUTING" on page 2-39.

CAUTION:

ECA14160

When installing the brake hose onto the
brake master cylinder, make sure the brake
pipe touches the projection “a” as shown.

2. Fill:

• Brake fluid reservoir

(to the maximum level mark “b”)

WARNING

EWA13090

• Use only the designated brake fluid.

Other brake fluids may cause the rubber
seals to deteriorate, causing leakage and
poor brake performance.

• Refill with the same type of brake fluid

that is already in the system. Mixing brake
fluids may result in a harmful chemical
reaction, leading to poor brake perfor-
mance.

Recommended fluid

DOT 4

Rear brake hose union bolt

30 Nm (3.0 m·kg, 22 ft·lb)

New

Recommended fluid

DOT 4

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands