Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 415 / 442

background image

ELECTRICAL COMPONENTS

8-88

EAS27990

CHECKING THE BULBS AND BULB SOCK-
ETS
Check each bulb and bulb socket for damage
or wear, proper connections, and also for conti-
nuity between the terminals.
Damage/wear

→

Repair or replace the bulb,

bulb socket or both.
Improperly connected

→

Properly connect.

No continuity

→

Repair or replace the bulb,

bulb socket or both.

Types of bulbs
The bulbs used on this vehicle are shown in
the illustration.
• Bulbs “a” are used for the headlights and

usually use a bulb holder that must be
detached before removing the bulb.

• Bulbs “b” is used for turn signal and can be

removed from the socket by pushing and
turning the bulb counterclockwise.

• Bulbs “c” are used for auxiliary lights and can

be removed from their respective socket by
carefully pulling them out.

Checking the condition of the bulbs
The following procedure applies to all of the
bulbs.
1. Remove:

• Bulb

WARNING

EWA13320

Since the headlight bulb gets extremely
hot, keep flammable products and your
hands away from the bulb until it has
cooled down.

CAUTION:

ECA14380

• Be sure to hold the socket firmly when

removing the bulb. Never pull the lead,
otherwise it may be pulled out of the ter-
minal in the coupler.

• Avoid touching the glass part of the head-

light bulb to keep it free from oil, other-

wise the transparency of the glass, the
life of the bulb, and the luminous flux will
be adversely affected. If the headlight
bulb gets soiled, thoroughly it with a cloth
moistened with alcohol or lacquer thin-
ner.

2. Check:

• Bulb (for continuity)

(with the pocket tester)
No continuity

→

Replace.

NOTE:

Before checking for continuity, set the pocket
tester to “0” and to the “

Ω

×

1” range.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the positive tester probe to termi-

nal “1” and the negative tester probe to ter-
minal “2”, and check the continuity.

b. If reading indicate no continuity, replace the

bulb.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Checking the condition of the bulb sockets
The following procedure applies to all of the
bulb sockets.
1. Check:

• Bulb socket (for continuity)

(with the pocket tester)
No continuity

→

Replace.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
413
414
415
416
417
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Tao Motor Pages: 3

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 44

Brand: Öhlins Pages: 8

prodrive SUR 3A00

Brand: Öhlins Pages: 4

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 4

Fastrax 50144-00

Brand: Dowco Pages: 3

Brand: zeeltronic Pages: 10

Brand: Baja motorsports Pages: 20

Brand: dushi Pages: 4

Brand: DYNATEK Pages: 4

Brand: IBEX Pages: 3

RIGID SADDLEBAG

Brand: Saddlemen Pages: 2

Road Sofa H18-07-18X all

Brand: Saddlemen Pages: 2

F12R AIR 50 cc. - Euro 2

Brand: Malaguti Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands