Yamaha YZF-R1 2007 Service Manual Download

Page: 157 / 442

FRONT BRAKE

4-28

EAS22360

DISASSEMBLING THE FRONT BRAKE
CALIPERS
The following procedure applies to both of the
brake calipers.
1. Remove:

• Brake caliper pistons “1”
• Brake caliper piston seals “2”

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Secure the right side brake caliper pistons

with a piece of wood “a”.

b. Blow compressed air into the brake hose

joint opening “b” to force out the left side
pistons from the brake caliper.

WARNING

EWA4C81005

• Never try to pry out the brake caliper pis-

tons.

• Do not loosen the bolts “3”.

c. Remove the brake caliper piston seals.
d. Repeat the previous steps to force out the

right side pistons from the brake caliper.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS22390

CHECKING THE FRONT BRAKE CALIPERS

1. Check:

• Brake caliper pistons “1”

Rust/scratches/wear

→

Replace the brake

caliper pistons.

• Brake caliper cylinders “2”

Scratches/wear

→

Replace the brake cali-

per assembly.

• Brake caliper body “3”

Cracks/damage

→

Replace the brake cali-

per assembly.

• Brake fluid delivery passages

(brake caliper body)
Obstruction

→

Blow out with compressed

air.

WARNING

EWA13600

Whenever a brake caliper is disassembled,
replace the piston seals.

EAS22410

ASSEMBLING THE FRONT BRAKE CALI-
PERS

WARNING

EWA13620

• Before installation, all internal brake com-

ponents should be cleaned and lubricated
with clean or new brake fluid.

• Never use solvents on internal brake

components as they will cause the piston
seals to swell and distort.

Recommended brake component replace-
ment schedule
Brake pads

If necessary

Piston seals

Every two years

Brake hoses

Every four years

Brake fluid

Every two years and
whenever the brake is
disassembled

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands