Yamaha YZF-R1 2007 Service Manual Download

Page: 102 / 442

ENGINE

3-15

2. Adjust:

• Clutch cable free play

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Handlebar side
a. Turn the adjusting bolt “1” in direction “b” or

“c” until the specified clutch cable free play
is obtained.

b. Tighten the locknut “1”.

NOTE:

If the specified clutch cable free play cannot be
obtained on the handlebar side of the cable,
use the adjusting nut on the engine side.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Engine side
a. Loosen the locknuts “1”.
b. Turn the adjusting bolt “2” in direction “a” or

“b” until the specified clutch cable free play
is obtained.

c. Tighten the locknuts “1”.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS20960

REPLACING THE AIR FILTER ELEMENT
1. Remove:

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

• Fuel tank side covers
• Fuel tank

Refer to "FUEL TANK" on page 7-1.

2. Remove:

• Air filter case cover “1”

Refer to "GENERAL CHASSIS" on page 4-
1.

3. Check:

• Air filter element “1”

Damage

→

Replace.

NOTE:

• Replace the air filter element every 40000

km (2400 mi) of operation.

• The air filter needs more frequent service if

you are riding in unusually wet or dusty
areas.

Clutch lever free play

10.0–15.0 mm (0.39–0.59 in)

Direction “b”

Clutch cable free play is increased.

Direction “c”

Clutch cable free play is decreased.

Direction “a”

Clutch cable free play is increased.

Direction “b”

Clutch cable free play is decreased.

Locknut

7 Nm (0.7 m·kg, 5.1 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands