Yamaha YZF-R1 2007 Service Manual Download

Page: 381 / 442

FUEL INJECTION SYSTEM

8-54

Fault code No.

Symptom

Open circuit detected in the primary lead of the cylinder-
#2 ignition coil.

Diagnostic code No.

Cylinder-#2 ignition coil

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

Connections
• Cylinder-#2 ignition coil coupler
• Main wire harness ECU coupler
• Sub-wire harness 1 coupler

• Check the couplers for any pins

that may be pulled out.

• Check the locking condition of

the couplers.

• If there is a malfunction, repair it

and connect the coupler
securely.

Cranking the
engine.
(Connect the
cylinder-#2 igni-
tion coil cou-
pler.)

Open or short circuit in wire harness
and/or sub-wire harness 1.

• Repair or replace if there is an

open or short circuit.

• Between cylinder-#2 ignition

coil coupler and ECU coupler.
(Red/Black–Red/Black)
(Gray/Red–Gray/Red)

Defective cylinder-#2 ignition coil.

• Execute the diagnostic mode.

(Code No.31)

• Test the primary and secondary

coils for continuity.

• Replace if defective.

Refer to "CHECKING THE
IGNITION COILS" on page 8-
95.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands