Yamaha YZF-R1 2007 Service Manual Download

Page: 96 / 442

ENGINE

3-9

NOTE:

“dIAG” appears on the odometer, tripmeter and
fuel reserve trip LCD.

3. Press the “SELECT” button to select the

CO adjustment mode “CO” or the diagnos-
tic mode “dIAG”.

4. After selecting “CO”, simultaneously press

the “SELECT” and “RESET” buttons for 2
seconds or more to execute the selection.

5. Press the “SELECT” and “RESET” buttons

to select a cylinder.

NOTE:

The selected cylinder number appears on the
odometer, tripmeter and fuel reserve trip LCD.
• To decrease the selected cylinder number,

press the “RESET” button.

• To increase the selected cylinder number,

press the “SELECT” button.

6. After selecting the cylinder, simultaneously

press the “SELECT” and “RESET” buttons
for 2 seconds or more to execute the selec-
tion.

7. Change the CO adjustment volume by

pressing the “SELECT” and “RESET” but-
tons.

NOTE:

The CO adjustment volume appears on the
tripmeter LCD.
• To decrease the CO adjustment volume,

press the “RESET” button.

• To increase the CO adjustment volume,

press the “SELECT” button.

8. Release the switch to execute the selec-

tion.

9. Simultaneously press the “SELECT” and

“RESET” buttons to return to the cylinder
selection (step 5).

10. Turn the main switch to “OFF” to cancel the

mode.

EAS20630

ADJUSTING THE THROTTLE CABLE FREE
PLAY

NOTE:

Prior to adjusting the throttle cable free play,
the carburetor synchronization should be
adjusted properly.

1. Check:

• Throttle cable free play “a”

Out of specification

→

Adjust.

2. Adjust:

• Throttle cable free play

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Handlebar side
a. Loosen the locknut “1”.
b. Turn the adjusting nut “2” in direction “a” or

“b” until the specified throttle cable free
play is obtained.

Throttle cable free play

3.0–5.0 mm (0.12–0.20 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands