Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 367 / 442

background image

FUEL INJECTION SYSTEM

8-40

41

Lean angle sensor:
open or short circuit
detected.

• Open or short circuit in wire harness.
• Defective lean angle sensor.
• Malfunction in ECU.

08

42

No normal signals are
received from the speed
sensor.

• Open circuit in wire harness.
• Malfunction in speed sensor.
• Malfunction in ECU.

07

Neutral switch:
open or short circuit
detected.

• Open circuit in wire harness.
• Malfunction in neutral switch.
• Malfunction in ECU.

21

43

Power supply to the injec-
tors and the fuel pump is
not normal.

• Open or short circuit in wire harness.
• Malfunction in ECU.

09

44

An error is detected while
reading or writing on
EEPROM (CO adjustment
value).

• Malfunction in ECU.

(The CO adjustment value is not properly
written on or read from the internal mem-
ory).

60

46

Power supply is not normal.

Malfunction in the charging system.
Refer to "CHARGING SYSTEM" on page 8-
11.

—

50

Faulty ECU memory.
(When this malfunction is
detected in the ECU, the
fault code number might not
appear on the meter.)

• Malfunction in ECU.

(The program and data are not properly
written on or read from the internal mem-
ory.)

—

59

Throttle position sensor (for
throttle cable pulley): open
or short circuit detected.
Throttle position sensor (for
throttle cable pulley) cou-
pler connection is loose.

• Open or short circuit in wire harness.
• Defective throttle position sensor.
• Improperly installed throttle position sensor.
• Malfunction in ECU.

14
15

60

Throttle servo motor:
open or short circuit
detected.
Defective throttle servo
motor.
Malfunction in ECU (servo
motor driving system).

• Open or short circuit in wire harness.
• Defective throttle servo motor (potentiome-

ter circuit).

• Stuck throttle servo motor (mechanism).
• Stuck throttle servo motor (motor).
• Malfunction in ECU.

01

Er-1

No signals are received
from the ECU.

• Open or short circuit in wire harness.
• Malfunction in meter.
• Malfunction in ECU.
• Defective wire connection of the ECU cou-

pler.

—

Er-2

No signals are received
from the ECU within the
specified duration.

• Improper connection in wire harness.
• Malfunction in meter.
• Malfunction in ECU.

—

Er-3

Data from the ECU cannot
be received correctly.

• Improper connection in wire harness.
• Malfunction in meter.
• Malfunction in ECU.

—

Fault
code

No.

Symptom

Probable cause of malfunction

Diagnostic

code No.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
365
366
367
368
369
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Xenith Pages: 17

Brand: Vance and hines Pages: 5

Brand: Baotian Pages: 22

Brand: Kinroad Pages: 27

Brand: Oxford Pages: 24

Brand: RSI Pages: 2

Brand: Livall Pages: 10

Brand: Yadea Pages: 88

Brand: hepco & becker Pages: 3

Brand: Gazzini Pages: 35

Classic 350 2019

Brand: Royal Enfield Pages: 126

Brand: Yerf-Dog Pages: 16

Brand: Bajaj Auto Pages: 83

Brand: Ohlins Pages: 12

Brand: LAS Pages: 53

Brand: Neco Pages: 22

Brand: Yamaha Pages: 686

Brand: Yamaha Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands