Yamaha YZF-R1 2007 Service Manual Download

Page: 290 / 442

CRANKSHAFT

5-83

NOTE:

• Align the projections “a” on the crankshaft

journal upper bearings with the notches “b” in
the upper crankcase.

• Be sure to install each crankshaft journal

upper bearing in its original place.

3. Install:

• Crankshaft

4. Install:

• Crankcase (lower)

Refer to "CRANKCASE" on page 5-65.

5. Install:

• Pin
• Pickup rotor “1”
• Drive sprocket “2”

Drive sprocket bolt

60 Nm (6.0 m·kg, 43 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands