Yamaha YZF-R1 2007 Service Manual Download

Page: 167 / 442

REAR BRAKE

4-38

EAS22560

INTRODUCTION

WARNING

EWA14100

Disc brake components rarely require dis-
assembly. Therefore, always follow these
preventive measures:
• Never disassemble brake components

unless absolutely necessary.

• If any connection on the hydraulic brake

system is disconnected, the entire brake
system must be disassembled, drained,
cleaned, properly filled, and bled after
reassembly.

• Never use solvents on internal brake

components.

• Use only clean or new brake fluid for

cleaning brake components.

• Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.

• Avoid brake fluid coming into contact

with the eyes as it can cause serious
injury.

• FIRST AID FOR BRAKE FLUID ENTERING

THE EYES:

• Flush with water for 15 minutes and get

immediate medical attention.

EAS22570

CHECKING THE REAR BRAKE DISC
1. Remove:

• Rear wheel

Refer to "REAR WHEEL" on page 4-14.

2. Check:

• Brake disc

Damage/galling

→

Replace.

3. Measure:

• Brake disc deflection

Out of specification

→

Correct the brake

disc deflection or replace the brake disc.
Refer to "CHECKING THE FRONT BRAKE
DISCS" on page 4-25.

4. Measure:

• Brake disc thickness

Measure the brake disc thickness at a few
different locations.
Out of specification

→

Replace.

Refer to "CHECKING THE FRONT BRAKE
DISCS" on page 4-25.

5. Adjust:

• Brake disc deflection

Refer to "CHECKING THE FRONT BRAKE
DISCS" on page 4-25.

6. Install:

• Rear wheel

Refer to "REAR WHEEL" on page 4-14.

EAS22580

REPLACING THE REAR BRAKE PADS

NOTE:

When replacing the brake pads, it is not neces-
sary to disconnect the brake hose or disas-
semble the brake caliper.

1. Remove :

• Screw plug “1”
• Brake pad pin “2”
• Brake caliper “3”
• Brake pad spring

2. Remove :

• Brake pads “1”

(along with the brake pad shims “2”)

Brake disc deflection limit

0.15 mm (0.0059 in)

Brake disc thickness limit

4.5 mm (0.18 in)

Rear brake disc bolt

30 Nm (3.0 m·kg, 22 ft·lb)
LOCTITE®

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands