Yamaha YZF-R1 2007 Service Manual Download

Page: 387 / 442

FUEL INJECTION SYSTEM

8-60

Fault code No.

Symptom

Power supply to the injectors and fuel pump is not nor-
mal.

Diagnostic code No.

Fuel system voltage (battery voltage)

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

Connections
• Relay unit coupler (fuel pump relay)
• Main wire harness ECU coupler

• Check the coupler for any pins

that may have pulled out.

• Check the locking condition of

the coupler.

• If there is a malfunction, repair it

and connect the coupler
securely.

Turning the
main switch to
“ON” when the
engine stop
switch is set to
“

”.

Open or short circuit in the wire har-
ness.

• Repair or replace if there is an

open or short circuit.

• Between relay unit coupler and

ECU coupler.
(Blue/Yellow–Blue/Yellow)
(Red/Blue–Red/Blue)

• Between relay unit coupler and

starter relay coupler.
(Red–Red)

• Between relay unit coupler and

right handlebar switch coupler.
(Red/Black–Red/Black)

Malfunction or open circuit in fuel
pump relay.

• Execute the diagnostic mode.

(Code No. 09)

• Replace if defective.
• If there is no malfunction with

the fuel pump relay, replace the
ECU.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands