Yamaha YZF-R1 2007 Service Manual Download

Page: 424 / 442

ELECTRICAL COMPONENTS

8-97

d. Measure the lean angle sensor out put volt-

age.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS4C81020

CHECKING THE STARTER MOTOR OPERA-
TION
1. Check:

• Starter motor operation

Does not operate

→

Perform the electric

starting system troubleshooting, starting
with step 4.
Refer to "TROUBLESHOOTING" on page
8-9.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the positive battery terminal “1”

and starter motor lead “2” with a jumper
lead “3”.

WARNING

EWA13810

• A wire that is used as a jumper lead must

have at least the same capacity of the bat-
tery lead, otherwise the jumper lead may
burn.

• This check is likely to produce sparks,

therefore, make sure no flammable gas or
fluid is in the vicinity.

b. Check the starter motor operation.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28150

CHECKING THE STATOR COIL
1. Disconnect:

• Stator coil coupler

(from the rectifier/regulator)

2. Check:

• Stator coil resistance

Out of specification

→

Replace the stator

coil.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

Ω

1) to the

stator coil coupler as shown.

b. Measure the stator coil resistance.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28170

CHECKING THE RECTIFIER/REGULATOR
1. Check:

• Charging voltage

Out of specification

→

Replace the rectifier/

regulator.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Set the engine tachometer to the ignition

coil of cylinder #1.

b. Connect the pocket tester (AC 20 V) to the

rectifier/regulator coupler as shown.

Stator coil resistance

0.14–0.18

Ω

at 20

C (68

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

White “1”

• Negative tester probe

White “2”

• Positive tester probe

White “1”

• Negative tester probe

White “3”

• Positive tester probe

White “2”

• Negative tester probe

White “3”

Charging voltage

14 V at 5000 r/min

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands