Yamaha YZF-R1 2007 Service Manual Download

Page: 186 / 442

FRONT FORK

4-57

a. Remove the rod puller attachment.
b. Install the nut.
c. Install the fork spring and spacer.

NOTE:

Install the spring with the smaller pitch “a” fac-
ing up “A”.

d. Reinstall the rod puller attachment
e. Press down in the spacer with the fork

spring compressor “1”

Pull up the rod puller and install the rod
holder “2” between the damper adjusting
rod locknut “3” and the spacer “4”.

NOTE:

Use the side of the rod holder that is marked
“A”.

g. Remove the rod puller and the rod puller

attachment.

h. Install the nut “1” and position it as speci-

fied “b”.

Set the cap bolt distance “c” to specifica-
tion.

Install the damper adjusting rod and cap
bolt, and then finger tighten the cap bolt.

k. Hold the cap bolt and tighten the damper

adjusting rod locknut to specification.

Remove the rod holder and fork spring
compressor.

Rod puller

90890-01437

Universal damping rod bleeding
tool set

YM-A8703

Rod puller attachment (M12)

90890-01435

Universal damping rod bleeding
tool set

YM-A8703

Fork spring compressor

90890-01441
YM-01441

Rod holder

90890-01434

Damper rod holder double
ended

YM-01434

Distance “b”

11 mm (0.43 in)

Distance “c”

13 mm (0.51 in)

Damper adjusting rod locknut

29 Nm (2.9 m·kg, 21 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands