Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 388 / 442

background image

FUEL INJECTION SYSTEM

8-61

Fault code No.

44

Symptom

An error is detected while reading or writing on EEPROM
(CO adjustment value).

Diagnostic code No.

60

EEPROM fault cylinder No.

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

1

Malfunction in ECU.

• Set the faulty cylinder’s exhaust

gas volume.
1 Execute the diagnostic mode

(Code No. 60) to check the
faulty cylinder number. (If mul-
tiple cylinders are defective,
the numbers of the faulty cyl-
inders are displayed alter-
nately at 2-second intervals.)

2 Execute the CO adjustment

mode and set the exhaust gas
volume of the faulty cylinder to
“0”.
Refer to "ADJUSTING THE
EXHAUST GAS VOLUME" on
page 3-8.

• Replace ECU if it does not

recover from the malfunction.

Turning the
main switch to
“ON”.
(Readjust the
exhaust gas vol-
ume after it is
reinstated.)

Fault code No.

46

Symptom Power supply is not normal.

Diagnostic code No.

—

—

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

1

Malfunction in rectifier/regulator

• Replace if defective.

Refer to "CHARGING SYS-
TEM" on page 8-11.

Starting the
engine and
operating it at
idle.

2

Open or short circuit in wire harness.

• Repair or replace if there is an

open or short circuit in the
charging system’s wiring.
Refer to "CHARGING SYS-
TEM" on page 8-11.

Fault code No.

50

Symptom

Faulty ECU memory. (When this malfunction is detected
in the ECU, the fault code number might not appear on
the meter.)

Diagnostic code No.

—

—

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

1

Malfunction in ECU.

Replace the ECU.

NOTE:

Be sure to turn the main switch to
“OFF” before replacing the ECU.

Turning the
main switch to
“ON”.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
386
387
388
389
390
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Honda Pages: 25

Brand: hepco & becker Pages: 5

Brand: SUR-RON Pages: 50

Brand: X-lite Pages: 76

Brand: kellermann Pages: 5

Brand: X-lite Pages: 33

Brand: Palm Pages: 14

Brand: Chicago Electric Pages: 8

Brand: Chicago Electric Pages: 12

Brand: Kobalt Pages: 27

Brand: Ultra-tow Pages: 6

Ranger XP900 A-Arms

Brand: SuperATV Pages: 6

Brand: hepco & becker Pages: 4

Brand: Honda Pages: 243

Brand: KTM Pages: 12

Brand: KTM Pages: 22

Brand: Polaris Pages: 136

Brand: Polaris Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands