Yamaha YZF-R1 2007 Service Manual Download

Page: 304 / 442

RADIATOR

6-3

EAS26390

CHECKING THE RADIATOR
1. Check:

• Radiator fins

Obstruction

→

Clean.

Apply compressed air to the rear of the
radiator.
Damage

→

Repair or replace.

NOTE:

Straighten any flattened fins with a thin, flat-
head screwdriver.

2. Check:

• Radiator hoses
• Radiator pipes

Cracks/damage

→

Replace.

3. Measure:

• Radiator cap opening pressure

Below the specified pressure

→

Replace

the radiator cap.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Install the radiator cap tester “1” and radia-

tor cap tester adapter “2” to the radiator
cap “3”.

b. Apply the specified pressure for ten sec-

onds and make sure there is no drop in
pressure.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

• Radiator fan

Damage

→

Replace.

Malfunction

→

Check and repair.

Refer to "RADIATOR" on page 6-1.

EAS26400

INSTALLING THE RADIATOR
1. Fill:

• Cooling system

(with the specified amount of the recom-
mended coolant)
Refer to "CHANGING THE COOLANT" on
page 3-20.

2. Check:

• Cooling system

Leaks

→

Repair or replace any faulty part.

Radiator cap opening pressure

108–137 kPa (15.4–19.5 psi)
(1.08–1.37 kgf/cm²)

Radiator cap tester

90890-01325
YU-24460-01

Radiator cap tester adapter

90890-01352
YU-33984

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands