Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 315 / 442

background image

FUEL TANK

7-2

EAS26630

REMOVING THE FUEL TANK
1. Extract the fuel in the fuel tank through the

fuel tank cap with a pump.

2. Remove:

• Fuel hose connector cover
• Fuel hose
• Fuel sender coupler
• Fuel pump coupler
• Fuel tank drain hose
• Fuel tank breather hose
• Fuel tank side cover

CAUTION:

ECA4C81002

• Be sure to disconnect the fuel hose by

hand. Do not forcefully disconnect the
hose with tools.

• Although the fuel has been removed from

the fuel tank be careful when removing
the fuel hoses, since there may be fuel
remaining in it.

NOTE:

• To remove the fuel hose from the fuel injec-

tion pipe, slide the cover “a” on the end of the
hose in the direction of the arrow shown and
then remove the hose.

• Before removing the hoses, place a few rags

in the area under where it will be removed.

3. Remove:

• Fuel tank

NOTE:

Do not set the fuel tank down so that the instal-
lation surface of the fuel pump is directly under
the tank. Be sure to lean the fuel tank in an
upright position.

EAS26640

REMOVING THE FUEL PUMP
1. Remove:

• Fuel pump

CAUTION:

ECA14720

• Do not drop the fuel pump or give it a

strong shock.

• Do not touch the base section of the fuel

sender.

EAS26670

CHECKING THE FUEL PUMP BODY
1. Check:

• Fuel pump body

Obstruction

→

Clean.

Cracks/damage

→

Replace the fuel pump

assembly.

2. Check:

• Diaphragms and gaskets

Turn/fatigue/cracks

→

Replace the fuel

pump assembly.

EAS26690

CHECKING THE FUEL PUMP OPERATION
1. Check:

• Fuel pump operation

Refer to "CHECKING THE FUEL PRES-
SURE" on page 7-6.

EAS26710

INSTALLING THE FUEL PUMP
1. Install:

• Fuel pump

NOTE:

• Do not damage the installation surface of the

fuel tank when installing the fuel pump.

• Always use a new fuel pump gasket.
• Install the fuel pump as shown in the illustra-

tion.

• Align the projection “a” on the fuel pump with

the slot in the fuel pump bracket.

• Tighten the fuel pump bolts in stages in a

crisscross pattern and to the specified
torque.

Fuel pump bolt

4 Nm (0.4 m·kg, 2.9 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
313
314
315
316
317
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Xenith Pages: 17

Brand: LAZER Pages: 6

Brand: hepco & becker Pages: 6

Brand: Qlink Pages: 44

Brand: BV Powersports Pages: 40

Brand: NewMar Pages: 116

Brand: DUCATI Performance Pages: 5

Brand: SUR-RON Pages: 50

Brand: Malossi Pages: 36

Brand: yasuni Pages: 12

Brand: Honda Pages: 224

Brand: MW TOOLS Pages: 9

STAR XV19CSX(C)

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 100

Star XV250B 2011

Brand: Yamaha Pages: 98

Brand: DYNATEK Pages: 4

1003007FONTANASPRINT

Brand: DYNATEK Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands