Yamaha YZF-R1 2007 Service Manual Download

Page: 190 / 442

STEERING HEAD

4-61

EAS23110

REMOVING THE LOWER BRACKET
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

2. Remove:

• Upper ring nut “1”

(with the steering nut wrench “2”)

WARNING

EWA13730

Securely support the lower bracket so that
there is no danger of it falling.

EAS23130

CHECKING THE STEERING HEAD
1. Wash:

• Bearings
• Bearing races

2. Check:

• Bearings “1”
• Bearing races “2”

Damage/pitting

→

Replace.

3. Replace:

• Bearings
• Bearing races

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the bearing races “1” from the

steering head pipe with a long rod “2” and
hammer.

b. Remove the bearing race “3” from the lower

bracket with a floor chisel “4” and hammer.

c. Install a new dust seal and new bearing

races.

CAUTION:

ECA14270

If the bearing race is not installed properly,
the steering head pipe could be damaged.

NOTE:

• Always replace the bearings and bearing

races as a set.

• Whenever the steering head is disassem-

bled, replace the rubber seal.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

• Upper bracket
• Lower bracket

(along with the steering stem)
Bends/cracks/damage

→

Replace.

EAS23140

INSTALLING THE STEERING HEAD
1. Lubricate:

• Upper bearing
• Lower bearing

Steering nut wrench

90890-01403

Spanner wrench

YU-33975

Recommended cleaning solvent

Kerosene

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands