manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 21   Serial Communication Interface with FIFO (SCIF) 

 

 

Rev.1.00  Dec. 13, 2005  Page 785 of 1286 

 

 REJ09B0158-0100 

Start of initialization

Clear TE and RE bits 

in SCSCR to 0 

Set TFCL and RFCL bits 

in SCFCR to 1 to clear 

the FIFO buffer  

After reading BRK, DR, 

and ER flags in SCFSR, 

write 0 to clear them  

Set CKE1 and CKE0 bits  

in SCSCR (leaving TE, RE, TIE, 

and RIE bits cleared to 0) 

Set data transfer format  

in SCSMR

Set value in SCBRR

1-bit interval elapsed?

Set RTRG1-0 and TTRG1-0 bits 

in SCFCR, and clear TFCL and  

RFCL bits to 0  

Set TE and RE bits in SCSCR  

to 1, and set TIE, RIE, 

and REIE bits 

Set external pins to be used  

(SCIF_SCK, SCIF_TXD,  

and SCIF_RXD)

End of initialization

Wait

No

Yes

Leave the TE and RE bits cleared
to 0 until the initialization almost
ends. Be sure to clear the TIE,
RIE, TE, and RE bits to 0.

Set the CKE1 and CKE0 bits.

Set the data transfer format in
SCSMR.

Write a value corresponding to
the bit rate into SCBRR. This
is not necessary if an external
clock is used. Wait at least one
bit interval after this write before
moving to the next step.

Set the external pins to be used.
Set SCIF_RXD input for reception and
SCIF_TXD output for transmission.
The input/output of the SCIF_SCK pin
must match the setting of the CKE1  
and CKE0 bits.

Set the TE or RE bit in SCSCR
to 1. Also set the TIE, RIE, and
REIE bits to enable the SCIF_TXD,
SCIF_RXD, and SCIF_SCK pins to
be used. When transmitting, the
SCIF_TXD pin will go to the mark
state. When receiving in clocked
synchronous mode with the
synchronization clock output (clock
master) selected, a clock starts to
be output from the SCIF_SCK pin
at this point.

[1]

[1]

[2]

[3]

[4]

[5]

[6]

[2]

[3]

[4]

[5]

[6]

 

Figure 21.16   Sample SCIF Initialization Flowchart 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

Rabbit 2000 Designers Handbook preview
2000
Brand: Rabbit Pages: 45
Rabbit 2000 Instruction & Reference Manual preview
2000
Brand: Rabbit Pages: 174
Rabbit 2000 Getting Started preview
2000
Brand: Rabbit Pages: 43
Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Brand: Laurell Pages: 84
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Variscite VAR-EXT-CB105 Datasheet preview
VAR-EXT-CB105
Brand: Variscite Pages: 18
ekwb EK-Loop Modulus Series User Manual preview
EK-Loop Modulus Series
Brand: ekwb Pages: 7
Uniden Data 2000 Manual preview
Data 2000
Brand: Uniden Pages: 5
ZALMAN CNPS11X Extreme User Manual preview
CNPS11X Extreme
Brand: ZALMAN Pages: 12
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
Z-Wave IOMOD10F Hardware User Manual preview
IOMOD10F
Brand: Z-Wave Pages: 42
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
AES BeBoPr++ User Manual preview
BeBoPr++
Brand: AES Pages: 44
Valcom VIP-814 Installation Manual preview
VIP-814
Brand: Valcom Pages: 3
MACHINIST X79-Z9-D7 User Manual preview
X79-Z9-D7
Brand: MACHINIST Pages: 15
peplink Balance 380 User Manual preview
Balance 380
Brand: peplink Pages: 111
TQ STKa64xxL Quick Start Manual preview
STKa64xxL
Brand: TQ Pages: 2
Crestron C2N-IO Installation Manual preview
C2N-IO
Brand: Crestron Pages: 2

Brands by name

Popular brands

Load more brands