manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 26   Serial Sound Interface (SSI) Module 

Rev.1.00  Dec. 13, 2005  Page 1008 of 1286 

REJ09B0158-0100 

 

8. Mute Enabled 

As basic sample format configuration except MUEN = 1 (TD data ignored)

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

SSI_SCK

SSI_WS

 SSI_SDATA

1st Channel

2nd Channel

 

Figure 26.17   Mute Enabled 

26.4.3 Compressed 

Modes 

The compressed mode is used to transfer a continuous bit stream. This would typically be a 
compressed bit stream which requires downstream decoding. 

In streaming transfer (burst mode not enabled) there is no concept of a data word. However in 
order to receive and transmit it is necessary to transfer between the serial bus and word formatted 
memory. Therefore the word boundary selection is arbitrary during receive/transmit and must be 
dealt with by another module. When burst mode is enabled then data bits being transmitted can be 
identified by virtue of the fact that the serial clock output is only activated when there is a word to 
be output and only the required number of clock pulses necessary to clock out each 32-bit word 
are generated. The serial bit clock stops at a low level when SSICR.SCKP = 0, and at a high level 
when SSICR.SCKP = 1. Note burst mode is only valid in the context of the SSI module being a 
transmitter of data. Burst mode data cannot be received by this module. 

Data is transmitted and received in blocks of 32 bits, and the first bit received/transmitted bit is bit 
31 when stored in memory. 

The word select pin in this mode does not act as a system word start signal as in non-compressed 
mode, but instead is used to indicate that the receiver can receive another data burst, or the 
transmitter can transmit another data burst. 

Figures 26.18 and 26.19 show the compressed mode data transfer, with burst mode disabled, and 
enabled, respectively. 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

GE D20MX User Manual preview
D20MX
Brand: GE Pages: 146
Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
Belkin F5D9001 Series Manual preview
F5D9001 Series
Brand: Belkin Pages: 72
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Cypress Semiconductor CY7C1019D Specification Sheet preview
CY7C1019D
Brand: Cypress Semiconductor Pages: 11
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Brand: Jaycar Electronics Pages: 2
ZALMAN CNPS7000A Series User Manual preview
CNPS7000A Series
Brand: ZALMAN Pages: 9
Sony Ericsson Developer's Board Manual preview
Developer's Board
Brand: Sony Ericsson Pages: 28
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
Corsair ELITE LCD UPGRADE KIT Manual preview
ELITE LCD UPGRADE KIT
Brand: Corsair Pages: 11
ADTRAN 1181413L2 Installation And Maintenance Manual preview
1181413L2
Brand: ADTRAN Pages: 100
TQ STKa64xxL Quick Start Manual preview
STKa64xxL
Brand: TQ Pages: 2
IEI Technology PUZZLE-5030 User Manual preview
PUZZLE-5030
Brand: IEI Technology Pages: 119
WAVESYS WSIL-1204-GT2-SFP2 Hardware User Manual preview
WSIL-1204-GT2-SFP2
Brand: WAVESYS Pages: 21
Acromag XVPX-6300 User Manual preview
XVPX-6300
Brand: Acromag Pages: 20
Fujitsu PRIMEPOWER 1500 Manual preview
PRIMEPOWER 1500
Brand: Fujitsu Pages: 21
Fujitsu Power Select D2703-S Short Description preview
Power Select D2703-S
Brand: Fujitsu Pages: 25
Fujitsu PRIMEPOWER 1 Hardware Platform Manual preview
PRIMEPOWER 1
Brand: Fujitsu Pages: 50

Brands by name

Popular brands

Load more brands