manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 15   Clock Pulse Generator (CPG) 

 

 

Rev.1.00  Dec. 13, 2005  Page 613 of 1286 

 

 REJ09B0158-0100 

Section 15   Clock Pulse Generator (CPG) 

The CPG generates clocks provided to both the inside and outside of the SH7780, and controls the 
power-down mode function. The CPG comprises a crystal oscillator circuit, PLLs, and a divider. 

15.1 Features 

The CPG has the following features. 

• 

Generates SH7780 internal clocks 

SH7780 internal clocks are: the CPU clock (Ick) which is used in the CPU, FPU, cache, and 
TLB; the SHwy clock (SHck) which is used by the SuperHyway bus; and peripheral clocks 
(Pck) which are used to interface with on-chip peripheral modules. 

• 

Generates SH7780 external bus clocks. 

SH7780 external bus clocks are the bus clock (Bck) which is used to interface with the external 
devices and memory clocks (DDRck) which are used in the DDRIF. 

• 

Selects two clock modes 
Selects a crystal resonator or an externally input clock as the CPG clock input. 

• 

Changes frequencies 

Changes frequencies of the internal clocks by the divider in the CPG. The divider is controlled 
with the frequency control register (FRQCR) set by software. 

• 

Provides the clock stop and module standby functions in control sleep mode 

Control sleep mode is the CPU stop mode. In control module standby mode, specific modules 
can be stopped. 

 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Brand: mikroElektronika Pages: 3
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Brand: Renesas Pages: 17
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Brand: MiLAN Pages: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Brand: Symantec Pages: 2
Baldor Modbus Plus Installation And Operating Manual preview
Modbus Plus
Brand: Baldor Pages: 34
H3C NSQ1GT48EA0 Manual preview
NSQ1GT48EA0
Brand: H3C Pages: 3
ZALMAN CNPS5700D-Cu User Manual preview
CNPS5700D-Cu
Brand: ZALMAN Pages: 7
Renesas R0E001000ACB00 User Manual preview
R0E001000ACB00
Brand: Renesas Pages: 4
ZALMAN CNPS 4X User Manual preview
CNPS 4X
Brand: ZALMAN Pages: 16
ADTRAN DUAL Nx56/64 1200142L1# User Manual preview
DUAL Nx56/64 1200142L1#
Brand: ADTRAN Pages: 48
Intellinet 560665 User Manual preview
560665
Brand: Intellinet Pages: 32
Moxa Technologies CP-102N-T Quick Installation Manual preview
CP-102N-T
Brand: Moxa Technologies Pages: 8
Patton electronics OnSite 9100 Quick Start Manual preview
OnSite 9100
Brand: Patton electronics Pages: 8
Acces I/O products mPCIe-ADI12-8 Hardware Manual preview
mPCIe-ADI12-8
Brand: Acces I/O products Pages: 13
Extreme Networks ExtremeCloud Appliance E3120 Installation Manual preview
ExtremeCloud Appliance E3120
Brand: Extreme Networks Pages: 27
Mobile Devices MUNIC V6+ Installation Manual preview
MUNIC V6+
Brand: Mobile Devices Pages: 12

Brands by name

Popular brands

Load more brands