manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 14   Direct Memory Access Controller (DMAC) 

Rev.1.00  Dec. 13, 2005  Page 576 of 1286 

REJ09B0158-0100 

 

Bit Bit 

Name 

Initial 
Value R/W Descriptions 

18 

HIE 

0 

R/W 

Half End Interrupt Enable  

Specifies whether an interrupt request is generated to 
the CPU when the number of transfers is decreased to 
half of the TCR value (a read transfer cycle end) set 
preceding the transfer. When the HIE bit is set to 1 and 
the HE bit is set, an interrupt request is generated to 
the CPU. To confirm the half end of the transfer, 
execute a dummy read of the destination space and 
issue the SYNCO instruction. Clear this bit to 0 while 
reload mode is set. This bit is valid in CHCR0 to 
CHCR3 and CHCR6 to CHCR9. 

0: Disables the half end interrupt 

1: Enables the half end interrupt 

17 AM  0  R/W 

Acknowledge 

Mode 

Selects whether DACK is output in data read cycle or in 
data write cycle. 

This bit is valid only in CHCR0 to CHCR3.  

0: DACK output in read cycle 

1: DACK output in write cycle 

16 AL  0  R/W 

Acknowledge 

Level 

Specifies whether the DACK signal output is high active 
or low active. 

This bit is valid only in CHCR0 to CHCR3.  

0: Low-active output of DACK (

DACK

) 

1: High-active output of DACK 

 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Brand: D-Link Pages: 4
DAD DSX 26 User Manual preview
DSX 26
Brand: DAD Pages: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Brand: D-Link Pages: 2
XtendLan NVR-xUD User Manual preview
NVR-xUD
Brand: XtendLan Pages: 228
H3C NIC-FC730i-Mb-2-32G Manual preview
NIC-FC730i-Mb-2-32G
Brand: H3C Pages: 37
FabiaTech Low Power Series User Manual preview
Low Power Series
Brand: FabiaTech Pages: 77
Omega OMB-DAQBOARD-500 Series User Manual preview
OMB-DAQBOARD-500 Series
Brand: Omega Pages: 48
Sony Ericsson Developer's Board Manual preview
Developer's Board
Brand: Sony Ericsson Pages: 28
NXP Semiconductors RDGD3160I3PH5EVB User Manual preview
RDGD3160I3PH5EVB
Brand: NXP Semiconductors Pages: 21
Ross ULTRIX-FM-NS-1RU Install Manual preview
ULTRIX-FM-NS-1RU
Brand: Ross Pages: 5
Proxim 68568r1 Installation And Management Manual preview
68568r1
Brand: Proxim Pages: 65
Omron G7Z Manual preview
G7Z
Brand: Omron Pages: 11
National Instruments NI 653x User Manual preview
NI 653x
Brand: National Instruments Pages: 147
Hameg HM6050-2K Manual preview
HM6050-2K
Brand: Hameg Pages: 46
TRENDnet TEW-221PC User Manual preview
TEW-221PC
Brand: TRENDnet Pages: 56
MSI TV@nywhere A/D Quick Installation Manual preview
TV@nywhere A/D
Brand: MSI Pages: 48
MSI MS-98C7 Manual preview
MS-98C7
Brand: MSI Pages: 54
MSI MS-98E2 Manual preview
MS-98E2
Brand: MSI Pages: 60

Brands by name

Popular brands

Load more brands