manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 26   Serial Sound Interface (SSI) Module 

 

 

Rev.1.00  Dec. 13, 2005  Page 1003 of 1286 

 

 REJ09B0158-0100 

In the case of the SSI module configured as a transmitter then each word that is written to SSITDR 
is transmitted in order on the serial audio bus. 

In the case of the SSI module configured as a receiver each word received on the Serial Audio Bus 
is presented for reading in order by SSIRDR. 

Figures 26.6 to 26.8 show how 4, 6 and 8 channels are transferred on the serial audio bus. 

Note that there are no padding bits in the first example, serial data is transmitted/received first and 
followed by padding bits in the second example, and padding bits are transmitted/received first 
and followed by serial data in the third example. This selection is purely arbitrary. 

MSB

LSB

Data

word 1

MSB

LSB MSB

LSB MSB

LSB

Data

word 2

Data

word 3

Data

word 4

System word 1

System word 2

MSB

LSB

Data

word 1

MSB

LSB MSB

LSB MSB

LSB

Data

word 2

Data

word 3

Data

word 4

System word 1

System word 2

LSB

MSB

SSI_SCK

 SSI_WS

SSI_SDATA

SCKP = 0, SWSP = 0, DEL = 1, CHNL = 01, SPDP = don't care, SDTA = don't care
 System word length = data word length 

×

 2 

 

Figure 26.6   Multi-channel Format (4 Channels, No Padding) 

MSB

LSB

System word 2

Data

word 1

MSB

LSB MSB

LSB

MSB

Data

word 2

Data

word 3

Padding

System word 1

MSB

LSB MSB

LSB MSB

LSB

Data

word 4

Data

word 5

Data

word 6

SSI_SCK

 SSI_WS

SSI_SDATA

Padding

SCKP = 0, SWSP = 0, DEL = 1, CHNL = 10, SPDP = 1, SDTA = 0
 System word length = data word length 

×

 3 

 

Figure 26.7   Multi-channel Format (6 Channels with High Padding) 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Brand: TE Connectivity Pages: 236
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
Renesas RL78/G11 User Manual preview
RL78/G11
Brand: Renesas Pages: 2
Arduino ABX00061 Reference Manual preview
ABX00061
Brand: Arduino Pages: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
ZALMAN ZM-2HC2 User Manual preview
ZM-2HC2
Brand: ZALMAN Pages: 8
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
Uctronics U6187 Assembly Manual preview
U6187
Brand: Uctronics Pages: 12
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Brand: FOR-A Pages: 37
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
VANTAS DPA-S50 Owner'S Manual preview
DPA-S50
Brand: VANTAS Pages: 30
Cypress Semiconductor CY7C1440AV33 Specification Sheet preview
CY7C1440AV33
Brand: Cypress Semiconductor Pages: 31
OPTO 22 BD-DEVNET User Manual preview
BD-DEVNET
Brand: OPTO 22 Pages: 28
IBM 55PUS8118 SCSI-2 Installation Manual preview
55PUS8118 SCSI-2
Brand: IBM Pages: 42

Brands by name

Popular brands

Load more brands