manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 11   Local Bus State Controller (LBSC) 

 

 

Rev.1.00  Dec. 13, 2005  Page 397 of 1286 

 

 REJ09B0158-0100 

11.5.10  Bus Release and Acquire Sequence 

The LBSC holds the bus itself unless it receives a bus request. 

On receiving an assertion (low level) of the bus request signal (

BREQ

) from off-chip, the LBSC 

releases the bus and asserts (drives low) the bus use permission signal (

BACK

) as soon as the 

currently executing bus cycle ends. On receiving the 

BREQ

 negation (high level) indicating that 

the slave has released the bus, the LBSC negates (drives high) the 

BACK

 signal and resumes use 

of the bus. 

The actual bus release sequence is as follows. 

First, the bus use permission signal is asserted in synchronization with the rising edge of the clock. 
The address bus and data bus go to the high-impedance state in synchronization from next rising 
edge of the clock after this 

BACK

 assertion. At the same time, the bus control signals (

BS

, 

CSn

, 

WE

, 

RD

, R/

W

, 

CE2A

, and 

CE2B

) go to the high-impedance state. These bus control signals are 

negated no later than one cycle before going to high-impedance. Bus request signal sampling is 
performed on the rising edge of the clock. 

The sequence for re-acquiring the bus from the slave is as follows. 

As soon as 

BREQ

 negation is detected on the rising edge of the clock, 

BACK

 is negated and bus 

control signal driving is started. Driving of the address bus and data bus starts at the next rising 
edge of an in-phase clock. The bus control signals are asserted and the bus cycle is actually 
started, at the earliest, at the clock rising edge at which the address and data signals are driven. 

In order to reacquire the bus and start execution of bus access, the 

BREQ

 signal must be negated 

for at least two cycles. 

Using the LCKN bit in CHCR of the DMAC, it is possible to restrain the bus release in the cycle 
between read and write access. 

If a DMA transfer is executed for the space that the source and destination address are in the 
LBSC space and the LCKN bit in CHCR is cleared to 0, the bus is not released in the cycle 
between read and write accesses even if the bus release signal (

BREQ

) is asserted. 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

IEI Technology WSB-H610 User Manual preview
WSB-H610
Brand: IEI Technology Pages: 187
IEI Technology TANK-XM811 User Manual preview
TANK-XM811
Brand: IEI Technology Pages: 71
Salus PL07 Instruction Manual preview
PL07
Brand: Salus Pages: 16
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
Zoom B9.1ut Operation Manual preview
B9.1ut
Brand: Zoom Pages: 88
Tandy 26-3814 Operation Manual preview
26-3814
Brand: Tandy Pages: 24
Thermaltake Extreme Spirit Il Instruction preview
Extreme Spirit Il
Brand: Thermaltake Pages: 2
Aviosys 9255W User Manual preview
9255W
Brand: Aviosys Pages: 77
Digi 9P 9360/9750 User Manual preview
9P 9360/9750
Brand: Digi Pages: 75
Optus Ultra WiFi Booster Quick Manual preview
Ultra WiFi Booster
Brand: Optus Pages: 8
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
ekwb EK-Quantum Vector FTW3 RTX 2080 Ti Installation Manual preview
EK-Quantum Vector FTW3 RTX 2080 Ti
Brand: ekwb Pages: 3
ADTRAN NetVanta 1224R Specifications preview
NetVanta 1224R
Brand: ADTRAN Pages: 4
RadiSys ES4001G ONT Quick Installation Manual preview
ES4001G ONT
Brand: RadiSys Pages: 6
Linksys EFG20 User Manual preview
EFG20
Brand: Linksys Pages: 37
Transition Networks PCM16-FX-LC-01 User Manual preview
PCM16-FX-LC-01
Brand: Transition Networks Pages: 5
TRENDnet TEG-S3M8S15 Specifications preview
TEG-S3M8S15
Brand: TRENDnet Pages: 2
WAVESYS WSIL-1204-GT2-SFP2 Hardware User Manual preview
WSIL-1204-GT2-SFP2
Brand: WAVESYS Pages: 21

Brands by name

Popular brands

Load more brands