manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 11   Local Bus State Controller (LBSC) 

Rev.1.00  Dec. 13, 2005  Page 370 of 1286 

REJ09B0158-0100 

 

11.5.4 

Burst ROM (Clock Asynchronous) Interface 

Setting the TYPE bit in CSnBCR (n = 0 to 2 and 4 to 6) to 010 allows a burst ROM (clock 
asynchronous memory) to be connected to areas 0 to 2 and 4 to 6. The burst ROM interface 
provides high-speed access to ROM that has a burst access function. The burst access timing of 
burst ROM is shown in figure 11.11. The wait cycle is set to 0 cycle. Although the access is 
similar to that of the SRAM interface, only the address is changed when the first cycle ends and 
then the next access is started. When 8-bit ROM is used, the number of consecutive accesses can 
be set as 4, 8, 16, or 32 through bits BST2 to BST0 in CSnBCR (n = 0 to 2 and 4 to 6). Similarly, 
when 16-bit ROM is used, 4, 8 or 16 accesses can be set; when 32-bit ROM is used, 4 or 8 
accesses can be set. 

The 

RDY

 signal is always sampled when one or more wait cycles are set.  

Even when no wait is specified in the burst ROM settings, two access cycles are inserted in the 
second and subsequent accesses as shown in figure 11.12. 

A writing operation for this interface is performed in the same way as for the SRAM interface. 

In a 32-byte transfer, a total of 32 bytes are transferred continuously according to the set bus 
width. The first access is performed on the data for which there was an access request, and the 
remaining accesses are performed in wraparound method according to the set bus width. The burst 
access is stopped once (negate the 

RD

) at the address boundary which is a bus width 

(CSnBCR.SZ) x burst length (CSnBCR.BST) address and then the access is resumed by the 
settings of CSnWCR. The bus is not released during this transfer. 

Figure 11.13 shows the timing chart when the burst ROM is used and setup/hold is specified by 
CSnWCR. 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

Mylex eXtremeRAID 1100 Installation Manual preview
eXtremeRAID 1100
Brand: Mylex Pages: 74
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
EMCIS LISN User'S Operating Manual preview
LISN
Brand: EMCIS Pages: 14
Mitsubishi 32172 User Manual preview
32172
Brand: Mitsubishi Pages: 874
Mellanox Technologies ConnectX 3 Pro User Manual preview
ConnectX 3 Pro
Brand: Mellanox Technologies Pages: 57
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
Juniper MX480 Hardware Manual preview
MX480
Brand: Juniper Pages: 420
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
Air Live AirVideo-100 Quick Setup Manual preview
AirVideo-100
Brand: Air Live Pages: 2
ICOP Technology VDX-6354RD User Manual preview
VDX-6354RD
Brand: ICOP Technology Pages: 42
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Brand: Microcomputer Systems Pages: 21
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Brand: Vivotek Pages: 46
FOLSOM Blend PRO BP-2002 Installation And Operator'S Manual preview
Blend PRO BP-2002
Brand: FOLSOM Pages: 89
M86 Security Web Filter HL User Manual preview
Web Filter HL
Brand: M86 Security Pages: 512
National Instruments USB device 622x User Manual preview
USB device 622x
Brand: National Instruments Pages: 23
Arctic Freezer i32 Welcome Manual preview
Freezer i32
Brand: Arctic Pages: 7

Brands by name

Popular brands

Load more brands