manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 20   Realtime Clock (RTC) 

Rev.1.00  Dec. 13, 2005  Page 716 of 1286 

REJ09B0158-0100 

 

20.3.7 Month 

Counter 

(RMONCNT) 

RMONCNT is an 8-bit readable/writable register used as a counter for setting and counting the 
BCD-coded month value in the RTC. It counts on the carry generated once per month by the day 
counter. 

The setting range is decimal 01 to 12. The RTC will not operate normally if any other value is set. 
Write processing should be performed after stopping the count with the START bit in RCR2, or 
by using the carry flag. 

RMONCNT is not initialized by a power-on or manual reset. 

Bits 7 to 5 are always read as 0. A write to these bits is invalid, but the write value should always 
be 0. 

0

1

2

3

4

5

6

7

—

—

—

—

—

0

10-month 

unit

—

0

0

1-month units

—

—

R/W

R/W

R/W

R/W

R/W

R

R

R

BIt:

Initial value:

R/W:

 

 

20.3.8 

Year Counter (RYRCNT) 

RYRCNT is a 16-bit readable/writable register used as a counter for setting and counting the 
BCD-coded year value in the RTC. It counts on the carry generated once per year by the month 
counter. 

The setting range is decimal 0000 to 9999. The RTC will not operate normally if any other value 
is set. Write processing should be performed after stopping the count with the START bit in 
RCR2, or by using the carry flag. 

RYRCNT is not initialized by a power-on or manual reset. 

0

1

2

3

4

5

6

7

8

9

10

11

12

13

15

14

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

1-year units

10-year units

100-year units

1000-year units

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

BIt:

Initial value:

R/W:

 

 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
Belkin F5D9001 Series Manual preview
F5D9001 Series
Brand: Belkin Pages: 72
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Brand: Dazzle Pages: 63
Neo Instruments Mini Vent User Manual preview
Mini Vent
Brand: Neo Instruments Pages: 2
XMOS XC-2 Quick Start Manual preview
XC-2
Brand: XMOS Pages: 6
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
Aqua Computer Aquaduct 240 eco Operating And Assembly Manual preview
Aquaduct 240 eco
Brand: Aqua Computer Pages: 20
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Brand: swiftech Pages: 2
IEI Technology TANK-101B User Manual preview
TANK-101B
Brand: IEI Technology Pages: 116
Transition Networks E-BR-SIC User Manual preview
E-BR-SIC
Brand: Transition Networks Pages: 1
LevelOne FUS-3100 Quick Installation Manual preview
FUS-3100
Brand: LevelOne Pages: 61
Ecolab EcoJet EcoStar 1500 Installation & Operation Manual preview
EcoJet EcoStar 1500
Brand: Ecolab Pages: 80
JETWAY 939GT2-Ultra Series User Manual preview
939GT2-Ultra Series
Brand: JETWAY Pages: 55

Brands by name

Popular brands

Load more brands