manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 14   Direct Memory Access Controller (DMAC) 

 

 

Rev.1.00  Dec. 13, 2005  Page 605 of 1286 

 

 REJ09B0158-0100 

not cleared in the procedure 4, then the transfer is stopped according to the condition of both 
the HE and the TE bits are set to 1. 

 

As explained above, a repeat mode transfer enables sequential voice compression by changing 
buffer for storing data received consequentially and a data buffer for processing signals 
alternately. 

14.4.6 

Reload Mode Transfer 

In a reload mode transfer, according to the settings of bits RPT[2:0] in CHCR,  the value set in 
SARB/DARB is set to SAR/DAR and the value of bits TCRB[23:16] is set in bits TCRB[7:0] at 
each transfer set in the bits TCRB[7:0], and the transfer is repeated until TCR becomes 0 without 
specifying the transfer settings again. A reload mode transfer is effective when repeating data 
transfer with specific area. Figure 14.12 shows the operation of reload mode transfer. 

DMAC

Bits RPT[2:0]

SHwy bus

CHCR

TCR

TCRB

SAR/DAR

SARB/DARB

Reload controller

Reload signal

Reload counter

Transfer counter

Transfer request

 

Figure 14.12   Reload Mode Transfer 

When a reload mode transfer is executed, TCRB is used as a reload counter. Set TCRB according 
to section 14.3.6, DMA Transfer Count Registers B0 to B3, B6 to B9 (TCRB0 to TCRB3, TCRB6 
to TCRB9). 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

GE D20MX User Manual preview
D20MX
Brand: GE Pages: 146
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
Juniper MX480 Hardware Manual preview
MX480
Brand: Juniper Pages: 420
Renesas R0E0144TNPFK00 User Manual preview
R0E0144TNPFK00
Brand: Renesas Pages: 4
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Brand: Inspired Energy Pages: 5
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Brand: ZALMAN Pages: 9
Net Optics Phantom HD Quick Install Manual preview
Phantom HD
Brand: Net Optics Pages: 2
Cypress Semiconductor CY7C68023 Specification Sheet preview
CY7C68023
Brand: Cypress Semiconductor Pages: 9
FabiaTech FB2701 User Manual preview
FB2701
Brand: FabiaTech Pages: 86
ADLINK Technology cPCI-3520 Series User Manual preview
cPCI-3520 Series
Brand: ADLINK Technology Pages: 81
National Instruments GPIB-ENET-1000 Installation Manual preview
GPIB-ENET-1000
Brand: National Instruments Pages: 35
IC Realtime nvr700ns User Manual preview
nvr700ns
Brand: IC Realtime Pages: 131

Brands by name

Popular brands

Load more brands