Renesas SH7780 Series Hardware Manual Download Page 477 | Manualshive

Page: 477 / 1340

background image

Section 12 DDR-SDRAM Interface (DDRIF)

Rev.1.00 Dec. 13, 2005 Page 427 of 1286

REJ09B0158-0100

V: Valid

data

The DESELECT command in table 12.6 is automatically issued whenever the SDRAM is not
being accessed by any module. The DESELECT command therefore cannot be explicitly issued
by the user.

12.5.4 SDRAM

Access

Mode

The DDRIF supports the following two SDRAM access modes. The BOMODE bits in MIM are
used to select the required mode.

Bank Open Mode: The SDRAM is accessed without the PRE command immediately after a
memory read or memory write, meaning that the bank is always open. This mode is useful for
applications in which a single bank is the target of consecutive memory accesses. When another
bank becomes the target, the PRE command is automatically issued.

Bank Closed Mode: Immediately after each round of reading or writing, the PRE command is
output and the target bank is closed. This mode is useful for applications in which the same bank
is unlikely to be the target of consecutive memory accesses.

12.5.5 Power-Down

Modes

(1) Self-Refresh

Mode

The self-refresh mode is a standby state in which the SDRAM generates its own refresh timing
and refresh addresses. Once the self-refresh mode has been set by setting the DRE and RMODE
bits in MIM to 1, the self-refresh state is retained even if the CPU enters the sleep mode. If an
interrupt then takes the CPU out of the sleep mode, the self-refresh state is still retained.

Although the SDRAM is made to enter the self-refresh state by simply setting registers of the
DDRIF, the sequence given below should be followed.

Note that in the transition from auto-refresh state to self-refresh state, the current auto-refresh state
should have been finished or been disabled before the transition.

[Transition to self-refresh state]

1. Confirm that transactions to the DDRIF are completed.

2. Through software control, set the SMS bits in SCR to issue the PREALL (precharge all-banks)

command. This closes any SDRAM bank that was open. After that, use the SMS bits in SCR
to issue the REFA (auto-refresh) command to ensure that all memory rows are refreshed.

«
...
475
476
477
478
479
...
»

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

Brand: D-Link Pages: 15

Brand: NEC Pages: 47

Brand: Ebyte Pages: 14

Brand: IBM Pages: 63

Brand: ForeScout Pages: 28

Brand: Barco Pages: 121

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Brand: UNA AUTOMATION Pages: 20

HHM Series HHM2245SA1

Brand: TDK Pages: 2

Brand: EMTRUST Pages: 103

Brand: Network Critical Pages: 200

crown PIP Series

Brand: Harman Pages: 16

Brand: Xantech Pages: 16

Brand: Kaya Instruments Pages: 48

Brand: netsys Pages: 164

Brand: Spirent Pages: 22

Brand: Xilinx Pages: 29

Brand: Freescale Semiconductor Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands