manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 21   Serial Communication Interface with FIFO (SCIF) 

 

 

Rev.1.00  Dec. 13, 2005  Page 753 of 1286 

 

 REJ09B0158-0100 

Bit Bit 

Name 

Initial 
Value R/W 

Description 

5 TDFE 

1  R/W

*

  Transmit FIFO Data Empty 

Indicates that data has been transferred from SCFTDR 
to SCTSR, the number of data bytes in SCFTDR has 
fallen to or below the transmit trigger data number set 
by bits TTRG1 and TTRG0 in SCFCR, and new 
transmit data can be written to SCFTDR. 

0: A number of transmit data bytes exceeding the 

transmit trigger set number have been written to 
SCFTDR 

[Clearing conditions] 

• 

When transmit data exceeding the transmit trigger 
set number is written to SCFTDR after reading 
TDFE = 1, and 0 is written to TDFE  

• 

When transmit data exceeding the transmit trigger 
set number is written to SCFTDR by the DMAC 

1: The number of transmit data bytes in SCFTDR does 

not exceed the transmit trigger set number (Initial 
value) 

[Setting conditions] 

• 

Power-on reset or manual reset 

• 

When the number of SCFTDR transmit data bytes 
falls to or below the transmit trigger set number as 
the result of a transmit operation

*

 

Note: As SCFTDR is a 64-byte FIFO register, the 

maximum number of bytes that can be written 
when TDFE = 1 is 64 - (transmit trigger set 
number). Data written in excess of this will be 
ignored. 
SCTFDR indicates the number of data bytes 
transmitted to SCFTDR. 

 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

D-Link DES-1210-08P Manual preview
DES-1210-08P
Brand: D-Link Pages: 15
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Brand: Paradyne Pages: 1
Amplifier Tech ATP6700 Owner'S Manual preview
ATP6700
Brand: Amplifier Tech Pages: 36
3Com Token Ring Getting Started Manual preview
Token Ring
Brand: 3Com Pages: 18
Supermicro SC836 X9 User Manual preview
SC836 X9
Brand: Supermicro Pages: 24
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
Renesas Converter Board R0E521237CFK00 User Manual preview
Converter Board R0E521237CFK00
Brand: Renesas Pages: 6
Icy Box IB-NAS5520 Quick Start Manual preview
IB-NAS5520
Brand: Icy Box Pages: 2
ETAS XETK-S22.0 User Manual preview
XETK-S22.0
Brand: ETAS Pages: 84
VideoWave Adam Device User Manual preview
Adam Device
Brand: VideoWave Pages: 12
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Brand: iesy Pages: 9
hilscher netHOST NHST-T100 User Manua preview
netHOST NHST-T100
Brand: hilscher Pages: 75
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
IBA FOB-SDexp Manual preview
FOB-SDexp
Brand: IBA Pages: 36
BOSER Technology HS-4703 Manual preview
HS-4703
Brand: BOSER Technology Pages: 78

Brands by name

Popular brands

Load more brands