manualshive.com logo in svg

Renesas SH7780 Series, Hardware Manual

The Renesas SH7780 Series offers exceptional performance in embedded systems. Access the comprehensive Hardware Manual for free download from our website manualshive.com, providing detailed instructions, diagrams, and specifications. Unlock the full potential of your device with this invaluable manual, tailored to enhance your user experience.

Share
Download
background image

Section 21   Serial Communication Interface with FIFO (SCIF) 

Rev.1.00  Dec. 13, 2005  Page 748 of 1286 

REJ09B0158-0100 

 

Bit Bit 

Name 

Initial 
Value R/W 

Description 

6 

RIE 

0 

R/W 

Receive Interrupt Enable 

Enables or disables generation of a receive-data-full 
interrupt (RXI) request when the RDF flag or DR flag in 
SCFSR is set to 1, a receive-error interrupt (ERI) 
request when the ER flag in SCFSR is set to 1, and a 
break interrupt (BRI) request when the BRK flag in 
SCFSR or the ORER flag in SCLSR is set to 1. 

0: Receive-data-full interrupt (RXI) request, receive-

error interrupt (ERI) request, and break interrupt 
(BRI) request disabled 

1: Receive-data-full interrupt (RXI) request, receive-

error interrupt (ERI) request, and break interrupt 
(BRI) request enabled 

Note: An RXI interrupt request can be cleared by 

reading 1 from the RDF or DR flag in SCFSR, 
then clearing the flag to 0, or by clearing the RIE 
bit to 0. ERI and BRI interrupt requests can be 
cleared by reading 1 from the ER, BRK, or 
ORER flag in SCFSR, then clearing the flag to 0, 
or by clearing the RIE and REIE bits to 0. 

5 TE  0  R/W 

Transmit 

Enable 

Enables or disables the start of serial transmission by 
the SCIF. 

Serial transmission is started when transmit data is 
written to SCFTDR while the TE bit is set to 1. 

0: Transmission disabled 

1: Transmission enabled

* 

Note: SCSMR and SCFCR settings must be made, the 

transmission format decided, and the transmit 
FIFO reset, before the TE bit is set to 1. 

 

Summary of Contents for SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7780 Series

Xilica Audio Design neutrino series Quick Start Manual preview
neutrino series
Brand: Xilica Audio Design Pages: 26
3Com 3CRSHPW196 User Manual preview
3CRSHPW196
Brand: 3Com Pages: 16
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
Renesas Compact Emulator M30620T-CPE User Manual preview
Compact Emulator M30620T-CPE
Brand: Renesas Pages: 52
Renesas RL78/G11 User Manual preview
RL78/G11
Brand: Renesas Pages: 2
Multitech ISI608PC Owner'S Manual preview
ISI608PC
Brand: Multitech Pages: 81
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Brand: B-G Instruments Pages: 4
ZALMAN ZM80C-HP Manual preview
ZM80C-HP
Brand: ZALMAN Pages: 18
Corsair H80i v2 Quick Start Manual preview
H80i v2
Brand: Corsair Pages: 12
Variscite VAR-EXT-CB103 Manual preview
VAR-EXT-CB103
Brand: Variscite Pages: 17
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Brand: PairGain Pages: 48
TERSUS Precis-BX305 Quick Start Manual preview
Precis-BX305
Brand: TERSUS Pages: 7
National Instruments NI 653x User Manual preview
NI 653x
Brand: National Instruments Pages: 147
Imagine communications Selenio SNP-GW-3GX32 User Manual preview
Selenio SNP-GW-3GX32
Brand: Imagine communications Pages: 153
VAMISOUND Schoeps electret Building Instructions preview
Schoeps electret
Brand: VAMISOUND Pages: 15
Freescale Semiconductor i.MX 6SoloLite Linux Reference Manual preview
i.MX 6SoloLite Linux
Brand: Freescale Semiconductor Pages: 199
Citizen IF1-WF04 User Manual preview
IF1-WF04
Brand: Citizen Pages: 50

Brands by name

Popular brands

Load more brands