manualshive.com logo in svg

NXP Semiconductors MPC5605BK, Reference Manual

Share
Download
NXP Semiconductors MPC5605BK Reference Manual Download Page 958

Appendix A Revision History

956

Freescale Semiconductor

Chapter 9, 

Reset Generation 

Module (MC_RGM)

Replaced 

Section 9.4.6, Boot mode capturing

 with the following:

The MC_RGM samples PA[9:8] whenever RESET is asserted until five FIRC (16 MHz internal 
RC oscillator) clock cycles before its deassertion edge. The result of the sampling is used at the 
beginning of reset PHASE3 for boot mode selection and is retained after RESET has been 
deasserted for subsequent boots after reset sequences during which RESET is not asserted.

Note:

 In order to ensure that the boot mode is correctly captured, the application needs to apply 

the valid boot mode value the entire time that RESET is asserted.

RESET can be asserted as a consequence of the internal reset generation. This will force 
re-sampling of the boot mode pins. (See 

Table 9-11

 for details.) 

Chapter 11, 

Voltage Regulators and 

Power Supplies

 Changed block in 

Figure 11-2 (Power domain organization)

 from 64K RAM (PD2/PD3 to 48 KB 

RAM (PD2). 

Chapter 12, 

Wakeup Unit (WKPU)

Removed column for 208 pkg from 

Table 12-1

; removed bullet point for 208 pkg from 

Section 12.5.2, Non-maskable interrupts

. 

Chapter 13, 

Real Time Clock / 

Autonomous Periodic 

Interrupt (RTC/API)

In 

Table 13-3 (RTCC field descriptions)

, added Note to RTCC[APIVAL] field description: 

Note: 

API functionality starts only when APIVAL is nonzero. The first API interrupt takes two 

more cycles because of synchronization of APIVAL to the RTC clock, and  1 cycles 
for subsequent occurrences. After that, interrupts are periodic in nature. The minimum 
supported value of APIVAL is 4. 

Chapter 16, 

Enhanced Direct 

Memory Access (eDMA)

Replaced entire 

Section 16.5.8, Dynamic programming

.

Chapter 19, 

Crossbar Switch (XBAR)

Updated 

Figure 19-1 (XBAR block diagram)

 to show eDMA as master.

In 

Table 19-1 (XBAR switch ports for MPC5606BK)

:

 • Added row for eDMA
 • Swapped Logical number and physical master ID
In 

Section 19.4, Features

, added bullet item for eDMA. 

Added row for eDMA to 

Table 19-2 (Hardwired bus master priorities)

, changed title of column for 

master ID to “Master #,” corrected master ID for “e200z0 core–CPU data” from 0 to 1. 

Throughout the chapter, corrected “two master ports” to “three master ports”. 

Chapter 21, 

Memory Protection Unit 

(MPU)

 In 

Section 21.5.2.1, MPU Control/Error Status Register (MPU_CESR)

, moved SPERR bitfield to 

bits 0:2, changed field tag to SPERR[0:2]. 

Moved MPU_EDR

n

[EACD] bits from 8:15 to 0:7 (

Figure 21-4

). 

Chapter 23, 

LIN Controller (LINFlex)

Added 

Section 23.8.2.1.7, Overrun

In 

Section 23.7.1.8, LIN output compare register (LINOCR)

, in 

Figure 23-13., LIN output compare 

register (LINOCR)

, changed the footnote to “If LINTCSR[LTOM] = 0, these fields are read-only.” 

Changed the first sentence of 

Section 23.8.3.1, LIN timeout mode

 to “Clearing the LTOM bit 

(setting its value to 0) in the LINTCSR enables the LIN timeout mode.” 

Changed the first sentence of 

Section 23.8.3.2, Output compare mode

 to “Setting 

LINTCSR[LTOM] = 1 enables the output compare mode.” 

Table A-1. Changes between revisions 1 and 2 (continued)

Chapter

Description

Summary of Contents for MPC5605BK





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands