manualshive.com logo in svg

NXP Semiconductors MPC5605BK, Reference Manual

Share
Download
NXP Semiconductors MPC5605BK Reference Manual Download Page 112

Chapter 6 Clock Description

MPC5606BK Microcontroller Reference Manual, Rev. 2

112

Freescale Semiconductor

 

6.5.2

Functional description

The SIRC provides a low frequency (f

SIRC

) clock of 128 kHz requiring very low current consumption. 

This clock can be used as the reference clock when a fixed base time is required for specific modules.

SIRC is always on in all device modes except STANDBY mode. In STANDBY mode, it is controlled by 
SIRC_CTL[SIRCON_STDBY] bit. The clock source status is updated in SIRC_CTL[S_SIRC] bit.

The SIRC clock can be further divided by a configurable division factor in the range from 1 to 32 to 
generate the divided clock to match system requirements. This division factor is specified by 
SIRC_CTL[SIRCDIV] bits.

The SIRC output frequency can be trimmed using SIRC_CTL[SIRCTRIM]. After a power-on reset, the 
SIRC is trimmed using a factory test value stored in test flash memory. However, after a power-on reset 
the test flash memory value is not visible at SIRC_CTL[SIRCTRIM], and this field shows a value of zero. 
Therefore, be aware that the SIRC_CTL[SIRCTRIM] does not reflect the current trim value until you have 
written to this field. Pay particular attention to this feature when you initiate a read-modify-write operation 
on SIRC_CTL, because a SIRCTRIM value of 0 may be unintentionally written back, and this may alter 
the SIRC frequency. In this case, you should calibrate the SIRC using the CMU or be sure that you only 
write to the upper 16 bits of this SIRC_CTL.

In this oscillator, two's complement trimming method is implemented. So the trimming code increases 
from –16 to 15. As the trimming code increases, the internal time constant increases and frequency 
reduces. Please refer to the device datasheet for average frequency variation of the trimming step.

6.5.3

Register description

Address: 0xC3FE_0080

Access: Read/write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

0

0

0

0

0

0

SIRCTRIM

W

RESET:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

0

0

0

SIRCDIV

0

0

0

S_SIRC

0

0

0

SIRCON_STDBY

W

RESET:

0

0

0

0

0

0

1

1

0

0

0

0

0

0

0

0

Figure 6-4. Low Power RC Control Register (SIRC_CTL)

Summary of Contents for MPC5605BK





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands