manualshive.com logo in svg

NXP Semiconductors MPC5605BK, Reference Manual

Share
Download
NXP Semiconductors MPC5605BK Reference Manual Download Page 370

Chapter 20 System Integration Unit Lite (SIUL)

MPC5606BK Microcontroller Reference Manual, Rev. 2

370

Freescale Semiconductor

 

It is important to note the bit ordering of the ports in the parallel port registers. The most significant bit of 
the parallel port register corresponds to the least significant pin in the port.

For example in 

Table 20-18

, the MPGPDO0 register contains field MASK0, which is the bitwise mask for 

Port A and field MPPDO0, which contains data to be written to Port A.

•

MPGPDO0[0] is the mask bit for Port A[0], MPGPDO0[1] is the mask bit for Port A[1] and so on, 
through MPGPDO0[15], which is the mask bit for Port A[15]

•

MPGPDO0[16] is the data bit mapped to Port A[0], MPGPDO0[17] is mapped to Port A[1] and so 
on, through MPGPDO0[31], which is mapped to Port A[15].

CAUTION

Toggling several IOs at the same time can significantly increase the current 
in a pad group. Caution must be taken to avoid exceeding maximum current 
thresholds. Please see data sheet.

20.5.3.15 Interrupt Filter Maximum Counter Registers (IFMC0–IFMC23)

These registers are used to configure the filter counter associated with each digital glitch filter.

NOTE

For the pad transition to trigger an interrupt it must be steady for at least the 
filter period. 

0x0C9C MPGPDO7

MASK7 (Port H)

MPPDO7 (Port H)

0x0CA0 MPGPDO8

MASK8 (Port I)

MPPDO8 (Port I)

0x0CAF MPGPDO9

MASK9 

(Port J)

Reserved

MPPDO9 

(Port J)

Reserved

1

SIU base address is 0xC3F9_0000. To calculate register address add offset to base address 

Table 20-19. MPGPDO0..MPGPDO9 field descriptions

Field

Description

MASK

x

[15:0]

Mask Field
Each bit corresponds to one data bit in the MPPDO

x

 register at the same bit location.

0 Associated bit value in the MPPDO

x

field is ignored

1 Associated bit value in the MPPDO

x

 field is written

MPPDO

x

[15:0]

Masked Parallel Pad Data Out
Write the data register that stores the value to be driven on the pad in output mode.
Accesses to this register location are coherent with accesses to the bitwise GPIO Pad Data Output 
Registers (GPDO0_3–GPDO148_151).
The x and bit index define which MPPDO register bit is equivalent to which PDO register bit 
according to the following equation:
MPPDO[

x

][

y

] = PDO[(

x

* 16) +

y

]

Table 20-18. MPGPDO0 – MPGPDO9 register map (continued)

Offset

1

Register

Field

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

Summary of Contents for MPC5605BK





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands