manualshive.com logo in svg

NXP Semiconductors MPC5605BK, Reference Manual

Share
Download
NXP Semiconductors MPC5605BK Reference Manual Download Page 328

Chapter 18 Interrupt Controller (INTC)

MPC5606BK Microcontroller Reference Manual, Rev. 2

328

Freescale Semiconductor

 

18.6.1.1

Peripheral interrupt requests

An interrupt event in a peripheral’s hardware sets a flag bit that resides in the peripheral. The interrupt 
request from the peripheral is driven by that flag bit.

The time from when the peripheral starts to drive its peripheral interrupt request to the INTC to the time 
that the INTC starts to drive the interrupt request to the processor is three clocks.

External interrupts are handled by the SIU (see 

Section 20.6.3, External interrupts

).

18.6.1.2

Software configurable interrupt requests

An interrupt request is triggered by software by writing a 1 to a SET

x

 bit in 

INTC_SSCIR0_3–INTC_SSCIR4_7. This write sets the corresponding flag bit, CLR

x

, resulting in the 

interrupt request. The interrupt request is cleared by writing a 1 to the CLR

x

 bit.

The time from the write to the SET

x

 bit to the time that the INTC starts to drive the interrupt request to the 

processor is four clocks.

18.6.1.3

Unique vector for each interrupt request source

Each peripheral and software configurable interrupt request is assigned a hardwired unique 9-bit vector. 
Software configurable interrupts 0–7 are assigned vectors 0–7 respectively. The peripheral interrupt 
requests are assigned vectors 8 to as high as needed to include all the peripheral interrupt requests. The 
peripheral interrupt request input ports at the boundary of the INTC block are assigned specific hardwired 
vectors within the INTC (see 

Table 18-1

).

18.6.2

Priority management

The asserted interrupt requests are compared to each other based on their PRI

x

 values set in the INTC 

Priority Select Registers (INTC_PSR0_3–INTC_PSR232_233). The result is compared to PRI in the 
associated INTC_CPR. The results of those comparisons manage the priority of the ISR executed by the 
associated processor. The associated LIFO also assists in managing that priority.

18.6.2.1

Current priority and preemption

The priority arbitrator, selector, encoder, and comparator subblocks shown in 

Figure 18-1

 compare the 

priority of the asserted interrupt requests to the current priority. If the priority of any asserted peripheral or 
software configurable interrupt request is higher than the current priority for a given processor, then the 
interrupt request to the processor is asserted. Also, a unique vector for the preempting peripheral or 
software configurable interrupt request is generated for INTC interrupt acknowledge register 
(INTC_IACKR), and if in hardware vector mode, for the interrupt vector provided to the processor.

18.6.2.1.1

Priority arbitrator subblock

The priority arbitrator subblock for each processor compares all the priorities of all of the asserted interrupt 
requests assigned to that processor, both peripheral and software configurable. The output of the priority 
arbitrator subblock is the highest of those priorities assigned to a given processor. Also, any interrupt 

Summary of Contents for MPC5605BK





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands