Basler BE1-CDS220, Instruction Manual

Page: 122 / 476

6-4 Reporting and Alarm Functions BE1-CDS220
>RG-STAT
INPUT(12345678) STATUS : 00000000
OUTPUT(A123456) STATUS : 0000000
CO-OUT(A123456) STATUS : LLLLLLL
CO-43 to CO-743 STATUS : 00000000
CO-101(101SC) STATUS : AFTER CLOSE(1)
CO-GROUP STATUS : L
ACTIVE LOGIC STATUS : BASIC-87
LOGIC VAR(00-31) STATUS : 00000000 00000000 00000000 00010000
LOGIC VAR(32-63) STATUS : 00000000 00000000 00000000 00000001
LOGIC VAR(64-95) STATUS : 00000000 00000000 00000000 00000000
ACTIVE GROUP STATUS : 0
BREAKER(52) STATUS : OFF
DIAG/ALARM STATUS : 0 RELAY, 0 LOGIC, 0 MAJOR, 0 MINOR
Input (1-8)
This line reports the status of contact sensing inputs IN1 through IN8. Input information is available at HMI
Screen 1.4.1, \STAT\OPER\INPUT, or with the RG-INPUT ASCII command. “0” indicates a de-energized
input and “1” indicates an energized input. See Section 3, Input and Output Functions, for more
information about contact sensing input operation.
Output (A, 1-6)
Output contact status for OUTA, OUT1 through OUT6 is reported on this line. This information is also
available at HMI Screen 1.4.2, \STAT\OPER\OUT, or with the RG-OUTSTAT ASCII command. “0”
indicates a de-energized output and “1” indicates an energized output. More information about output
contact operation is available in Section 3, Input and Output Functions.
CO-OUT (A,1-6)
This line reports the logic override of the output contacts. Logic override status is reported at HMI Screen
2.4, \CTRL\OUT, and through the RG-OUTCNTRL ASCII command. Section 3, Input and Output
Functions, provides more information about output logic override control.
CO-43 to CO-743
Virtual switch function status is reported on this line. This information is also available at HMI Screen
1.4.3, \STAT\OPER\x43, where x is blank, 1, 2, 3, 4, 5, 6, or 7. The status of the 43 switches is also
available from the RG-43STAT ASCII command. See Section 4, Protection and Control, Virtual Switches,
for more information about this function.
CO-101
These lines report the status of the slip contact output of the virtual breaker control switch. This
information is available on HMI Screen 2.2, \CTRL\BKR, or with the RG-101STAT ASCII command. See
Section 4, Protection and Control, Virtual Switches, for more information about this function.
CO-GROUP
This line reports the status of the logic override of the setting group selection function. This information is
available on HMI Screen 2.3, \CTRL\SG, or using the RG-GRPCNTRL ASCII command. See Section 4,
Protection and Control, Setting Groups, for more information on this function.
Active Logic
This line reports the name of the active logic scheme. The active logic scheme name can also be viewed
at HMI Screen 5, \PROT, or with the RG-LOGIC ASCII command. See Section 7, BESTlogic
Programmable Logic, Logic Schemes, for more information about active logic.
Logic Variables (00-31), (32-63), and (64-95)
These three lines report the status of each of the BESTlogic variable. The output of these lines can be
entered into Table 6-3 to determine the status of each logic variable. See Section 7, BESTlogic
Programmable Logic, for more information about BESTlogic Variables. This information is not available
from the HMI. RL (report logic) also reports the BESTlogic logic variables.