Vista 5 M3 Digital Mixing System
AutoTouchPlus 5-67
Document generated: 28.08.13
SW V4.9
5.9.4
Auto Punch-In/Out
Automatic punch-in/punch-out is controlled via the AutoTouchPlus window
of the GC.
Write Zone
To set up an
Auto Punch In/Out
, a
Write Zone
with a
Begin
and
End
time
must first be established. These will be the
In
and
Out
points for the
Auto
Punch In/Out
. The times displayed were the last
In
and
Out
times used by
the system. Direct entry of
Begin
and
End
times is possible once the
Write
Zone
is enabled. Refer to
chapter 5.9.3
for details.
Auto Punch In
To activate the
Auto Punch In
feature, the
Write Zone
must first be enabled,
which is done by checking the
Enabled
box next to the
End
time field. Once
the
Write Zone
is enabled, it is then possible to enable the
Auto Punch In
facility. This is accomplished by checking the
Auto Punch In
box located
below the
Write Zone
Enabled
box.
Performing the Punch
Once
Auto Punch In
is enabled and the desired controls are enabled, play
back timecode (media). During the pre-roll before the
Begin
Time, the af-
fected controls will act as if in RECORD ENABLE, but will not punch-in
until the
Write Zone
Begin
time.
At the
Begin
time, the system will automatically punch in and any enabled
controls will change to RECORD. Recording will continue until the
End
time
is reached, where the controls are automatically punched out.
Notes
It is possible to punch-out any individual control at any time within the
Write
Zone
using the
ISO (AUTO MODE)
key. Global punch-outs may also take place
before the end of the
Write Zone
. It is not possible to punch-in before the
Begin time or after the End time when the
Write Zone
is enabled.
Glide functions may be used with Auto Punch-In/Out. Since changes to the
Read Mix are prohibited after the
Write Zone
End time, the Backtime Glide
function must be used if Auto Punch-out is used.
5.9.5
Auto Global Punch-In/Out
Global Punch-Ins and Punch-Outs can also be done via the GPI input. This will
basically make the
Punch In
and
Punch Out
buttons available to external
systems or external keys.
If such functionality is required, the
Signaling.ini
file needs to be adapted
accordingly. Please contact Studer Service & Support to do the necessary
changes in that file.
Summary of Contents for Vista 5 M3
