Vista 5 M3 Digital Mixing System
5-88 AutoTouchPlus
Document generated: 28.08.13
SW V4.9
Channel Patch Operations
Channel Patch items are operated as follows:
• Input Selector: Place the cursor on or near the Input Selector icon. Each
trackball click will cycle the selector through the inputs. A Touch event
will be produced for each click.
• Processor Block Order: Click and hold the processor block to be moved,
drag it to the new location, and release the trackball button (click and drag).
A Touch event will be produced when the trackball is released.
• Dynamic Sidechain Link Setup: Clicking Sidechain Link Setup will open
the Sidechain Link window where channels may be added to the available
Sidechain Links. A Touch event will be produced when the ‘ADD’ button
is clicked.
• Dynamic Sidechain Link Enable: Clicking the Check Box will toggle the
switch state. A Touch event will be produced when the box is checked or
unchecked.
• Dynamic Key Input Routing: The route with the solid line is the current
state. Clicking the dashed line will select that route and a Touch event will
be produced.
• Direct Output Tap Location: The route with the solid line is the current
state. Clicking the dashed line will select that route and a Touch event will
be produced.
• Meter Feed Tap Location: Clicking the alternate location (shown grayed-
out) will select that location and a Touch event will be produced.
Channel Patch Switches
Two Channel Patch items operate as toggle Switches:
• Dynamic Sidechain Link Setup
• Dynamic Sidechain Link Enable
From the Channel Patch, these switches follow the rules of Press and Release
switch operations. However, if these functions are accessed via the channel
strip keys, they may use either Press and Release or Press and Hold opera-
tions. Press and Hold functions are not available via the GC.
As with any control, changes to Channel Patch items may Auditioned.
Record a Channel Patch Change
To automate an item in the Channel Patch, use the following procedure:
1.
Select the desired global Control Mode.
Write
will overwrite previous
changes, both location and connection type.
2.
Select
TOUCH – Record
.
3.
Select the desired
Write To:
and
Extend Back To:
functions.
4.
Open the Channel Patch if it is not already open.
5.
Perform the desired operation within the Channel Patch.
6.
At the time the desired operation is performed, AutoTouchPlus will
punch-in. The new item state will persist until the
Write To:
conditions
are met or a Global Punch-out occurs.
7.
When timecode is stopped, a new Mix Pass will be generated.
Summary of Contents for Vista 5 M3
