manualshive.com logo in svg

LAPIS Semiconductor ML62Q1000 Series, User Manual, Page: 476 / 882

Share
Download
LAPIS Semiconductor ML62Q1000 Series User Manual Download Page 476

ML62Q1000 Series User's Manual 

Chapter 12

 

I2C Bus Unit

 

FEUL62Q1000 

12-20 

Bit no. 

Bit symbol 

name 

Description 

4 

I2US0TR 

This bit is used to indicate the transmitting or receiving state in the slave mode. 

This bit is set to "1" when detecting the I2UM0RW bit of I2UM0SA register is "1" (data 
received mode). This bit is reset to "0" when detecting a stop condition or detecting the 
I2UM0RW bit is "0" (data transmission mode). 

To reset the I2US0TR bit not in the case detecting a stop condition, write "1" to this bit or write 
"0" to I2US0EN bit of I2US0MD register. 

0:

 

Receiving state (Initial value) 

1:

 

Transmitting state 

3 

I2US0SAA   

This bit is used to indicate that this device is specified as a slave address in the slave mode. 

This bit is set to "1" when the content of the slave address output by the master device 
coincides with the contents of I2US0SA register. This bit is reset to "0" when a stop condition 
is received. 

To reset the I2US0SAA bit, write "1" to this bit or write "0" to I2US0EN bit of I2US0MD 
register. 

0:

 

  Not coincide with the slave address (initial value) 

1:

 

  Coincides with the slave address 

2 

I2US0ER 

This bit is used to indicate a transmission error in the slave mode. 

When the value of the bit transmitted and the value of the I2CU0_SDA pin do not coincide, 
this bit is set to "1". When this bit is set to "1", the I2CU0_SDA pin output is disabled until the 
subsequent byte data communication terminates. 

To reset the I2US0ER bit, write "1" to this bit or write "0" to I2US0EN bit of I2US0MD register. 

0:

 

  There was no transmission error (initial value) 

1:  There was a transmission error 

1 

I2US0ACR 

This bit is used to store an acknowledgment signal received in the slave mode. 

The acknowledgment signals are received each time the slave address is received and data 
transmission or reception is completed. 

To reset the I2US0ACR bit, write "1" to this bit or write "0" to I2US0EN bit of I2US0MD 
register. 

0:

 

  Received the acknowledgment "0" (initial value) 

1:

 

  Received the acknowledgment "1" 

0 

I2US0BB 

This bit is used to indicate the state of use of the I

2

C bus in the slave mode. 

When the start condition is generated on the I

2

C bus, this bit is set to "1" and when the stop 

condition is generated, this bit is reset to "0". 

To reset the I2US0BB bit, write "1" to this bit or write "0" to I2US0EN bit of I2US0MD register. 

0:

 

I

2

C bus-free state (initial value) 

1:

 

I

2

C bus-busy state 

 
 

[Note] 

Ÿ

 

Do not update each bit of the I2UM0STA register by using the bit symbol. Update it by using a byte 
access, not so that unintented bits are changed by the bit access instructions. 

 

 

Summary of Contents for ML62Q1000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments