manualshive.com logo in svg

Intel 8XC196NT, User Manual

Share
Download
Intel 8XC196NT User Manual Download Page 328

14-9

INTERFACING WITH EXTERNAL MEMORY

1

IRC2

Ready Control

This bit, along with IRC0 (CCR0.4) and IRC1 (CCR0.5), limits the 
number of wait states that can be inserted while the READY pin is held 
low. Wait states are inserted into the bus cycle either until the READY 
pin is pulled high or until this internal number is reached.

IRC2 IRC1 IRC0
0

0

0

zero  wait  states

0

X

1

illegal

1

1

X

illegal

1

0

0

one  wait  state

1

0

1

two  wait  states

1

1

0

three  wait  states

1

1

1

infinite

0

LDCCB2

Load CCB2

Setting this bit causes CCB2 to be read.

CCR1 (Continued)

Address:

Reset State:

FF201AH

XXH

The chip configuration 1 (CCR1) register enables the watchdog timer and selects the bus timing 
mode. Two of its bits combine with three bits of CCR0 to control wait states and bus width. Another bit 
controls whether CCR2 is loaded.

7

0

MSEL1

MSEL0

0

1

WDE

BW1

IRC2

LDCCB2

Bit 

Number

Bit 

Mnemonic

Function

Figure 14-2.  Chip Configuration 1 (CCR1) Register (Continued)

           

Summary of Contents for 8XC196NT






















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands