GRAUPNER mx-20 Hott, Programming Manual

Page: 143 / 296

143 Detail program description - Control adjust
Alarm timer
SEL
––– 0:00
0:00
0:00
0s
0s –––
–––
–––
–––
SEL
0s Timer1
Timer2
Timer3
Lap time/tim tab
Lap Display
The input fi eld in the "Alarm" column is activated by
tapping the center
SET key on the right touch pad. In
this fi eld, use the arrow keys on the left or right touch
pad to defi ne a time between 5 and 90 seconds (in
5-second increments) before zero is reached: at this
point an audible signal will be emitted, which eliminates
the need for you to check the screen continually during
the fl ight.
Audible signal sequence
30 s before zero: Triple beep
Single beep every two seconds
20 s before zero: Double beep
Single beep every two seconds
10 s before zero: Single beep|
Single beep every second
5 s before zero: Single, higher-frequency beep
every second
Zero: Extended audible signal and
screen switches to highlighted
display
Tapping the

or

keys on the right touch pad at
the same time ( CLEAR ) will reset the values entered in
the currently active fi eld to "0s".
Note:
If timer functionality has been changed at any point, then
the new changes to settings are made active only after
the timer(s) have been stopped on the basic display and
by then tapping the

or

keys on the right touch
pad at the same time ( CLEAR ) to reset them.
Like the two standard timers positioned above it, this
third, phase-specifi c timer is reset to its starting value
by simultaneously tapping the

or

keys on
the right touch pad ( CLEAR ). It is stopped in all fl ight
phases at the same time, even if it has not been stopped
separately in the other fl ight phases.
Lap counter/timetable
SEL
––– 0:00
0:00
0:00
0s
0s –––
–––
–––
–––
SEL
0s Timer1
Timer2
Timer3
Lap time/tim tab
Lap Display
On the "Lap time/tim tab" line, assign a switch only
as described in the section "Assigning transmitter
controls, switches and control switches" (page 52).
Preferably, you should make use of one of the two
momentary switches (SW 1 or 9) at this point: in this
way, the lap count is incremented each time by one lap
while simultaneously (and automatically) the lap time
elapsed during this lap is stopped (and recorded). This
momentary switch simultaneously starts the stopwatch
for the next lap. As the timer is triggered, the lap or
switch impulse counter is shown highlighted.
GRAUBELE
#01
2:22h
Stop
Flt
«Speed »
K78
0:00
0:00
5.5V
5.2V 0:00.0
M
Lap
2:33.4
11
"Time1" and "Time2" operate in the same manner; for
more details please read the section on the "
Phase
settings " menu option.
Up to 99 lap times can be recorded and accessed,
each with a maximum duration of 99 minutes and
59.9 seconds.
To stop the timer in question, tap the center
ESC key on
the left touch pad on the basic display after the fl ight is
over. The lap or switch impulse counter is now shown in
"normal" mode:
GRAUBELE
#01
2:22h
Stop
Flt
«Speed »
K78
0:00
0:00
5.5V
5.2V 0:00.0
M
Lap
4:33.2
22
If you tap the

or

keys on the right touch pad
at the same time ( CLEAR ), this resets the counter to
"00" and deletes the stored times . However, the timers
must have been stopped before this.
Notes:
If you have selected a normal switch to operate the •
lap counter, take care to ensure that this switch is set
to "OFF" before you press the center
ESC button on
the left touch pad.