Nortel 425-24T Скачать руководство пользователя страница 270

Страница: 270 / 488

270

Chapter 7 System configuration using the CLI

320985-A Rev 01

copy running-config tftp command

This command copies contents of the current configuration file to another file on
the TFTP server. The syntax of the command is

copy running-config tftp {<address> <filename>}

This command can be executed in the config mode.

Table 72

describes the parameters and variables of this command.

Customizing your system

You can customize your system using the CLI commands described in this
section. This section covers the following topics:

•

“Setting the terminal” on page 270

•

“Displaying system information” on page 273

•

“Setting boot parameters” on page 274

•

“Setting TFTP parameters” on page 276

•

“Setting the default management interface” on page 279

•

“Customizing the opening banner” on page 280

•

“Setting the default management interface” on page 279

Setting the terminal

You can view the terminal settings, set them to default settings, or customize the
terminal settings. This sections covers:

Table 72

copy running-config tftp command parameters and variables

Parameter Description

address

Signifies the IP address of the TFTP server

filename

Denotes the filename to store configuration commands

on the TFTP server

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 270 / 488

Результаты поиска

Содержание 425-24T

Отзывы: