manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 317 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 317

Chapter 7 System configuration using the CLI

317

System Configuration Guide

 

The software download process automatically completes without user 
intervention. The process erases the contents of flash memory and replaces it with 
a new software image. Take care not to interrupt the download process until after 
it runs to completion (the process can take up to 10 minutes, depending on 
network conditions).

When the download process is complete, the switch automatically resets and the 
new software image initiates a self-test. The system returns a message after 
successfully downloading a new image. 

Figure 123

 shows a sample output of the download command.

Figure 123   

download message for Ethernet Switch 425-48T

During the download process, the Ethernet Switches 325 and 425 is not 
operational. You can monitor the progress of the download process by observing 
the LED indications.

diag <filename>

Enter the name of the Ethernet Switches 325 and 425 diagnostics 
image you want to download.

no-reset

Download the specified software without resetting the unit.

Table 105   

download command parameters and variables

Parameters and 
variables

Description

Download Image [/]

Saving Image [-]

Finishing Upgrading Image

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов