Nortel 425-24T Скачать руководство пользователя страница 291

Страница: 291 / 488

Chapter 7 System configuration using the CLI

291

System Configuration Guide

sntp server primary address command

The

sntp server primary address

command specifies the IP addresses of

the primary NTP server. The syntax for the

sntp server primary address

command is:

sntp server primary address

A.B.C.D>

The

sntp server primary address

command is in the config command

mode.

Table 85

describes the parameters and variables for the

sntp server primary

address

command.

The default is 0.0.0.0.

sntp server secondary address command

The

sntp server secondary address

command specifies the IP addresses

of the secondary NTP server. The syntax for the

sntp server secondary

address

command is:

sntp server secondary address

A.B.C.D>

The

sntp server secondary address

command is in the config command

mode.

Table 85

sntp server primary address command parameters and variables

Parameters and
variables

Description

<A.B.C.D>

Enter the IP address of the primary NTP server.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 291 / 488

Результаты поиска

Содержание 425-24T

Отзывы: