Nortel 425-24T Скачать руководство пользователя страница 439

Страница: 439 / 488

Default settings

439

System Configuration Guide

Bridge Priority

0x8000

Spanning Tree Switch Settings screen
in RSTP mode (see

Configuring VLANs,
Spanning Tree, and
MultiLink Trunking for Nortel
Ethernet Switches 325 and 425,
Software Release 3.6

(320986-A))

Root Port

Root Path Cost

Maximum Age Time

20 seconds

Forward Delay

15 seconds

Bridge Hello Time

20 seconds

Bridge Max. Age Time

20 seconds

Bridge Forward Delay Time

15 seconds

Create STP Group

Spanning Tree Group Configuration
screen in MSTP mode (see

Configuring VLANs,
Spanning Tree, and
MultiLink Trunking for Nortel
Ethernet Switches 325 and 425,
Software Release 3.6

(320986-A))

Delete STP Group

Blank

Bridge Priority

0x8000

Bridge Hello Time

2 seconds

Bridge Maximum Age Time

20 seconds

Bridge Forward Delay Time

15 seconds

Add VLAN membership

Delete VLAN Membership

Blank

STP Group State

Active for CIST; InActive for
MSTIs 2 to 7.

Participation

Normal Learning

Spanning Tree Port Configuration
screen in MSTP mode (see

Configuring VLANs,
Spanning Tree, and
MultiLink Trunking for Nortel
Ethernet Switches 325 and 425,
Software Release 3.6

(320986-A))

Priority

128

Path Cost

200000 (20 000 for Gigabit
port)
Path Cost = 2*10

/(Number

of Kilobits/link)

State

Topology dependent

Table 167

Factory default settings (continued)

Field

Default setting

Appears in this CI screen

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 439 / 488

Результаты поиска

Содержание 425-24T

Отзывы: