manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 243 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 243

Chapter 6 System configuration using the Console Interface

243

System Configuration Guide

 

Requirements

The following requirements apply to the Configuration File feature:

•

The Configuration File feature can only be used to copy 

standalone switch

 

configuration parameters to

 

other standalone switches

 or to copy 

stack 

configuration parameters to other stack configurations

.

For example, you cannot duplicate the configuration parameters of a unit in a 

stack

 configuration and use it to configure a 

standalone

 switch.

•

A configuration file obtained from a standalone switch can only be used to 
configure other standalone switches that have the same firmware revision and 
model type as the donor standalone switch.

•

A configuration file obtained from a stack unit can only be used to configure 
other stacks that have the same number of switches, firmware version, model 
types, and physical IDs as the stack the donor stack unit resides in.

Reconfigured stacks are configured according to the unit order number of the 
donor unit. For example, the configuration file parameters from a donor unit 
with physical ID 

x

 are used to reconfigure the unit with physical ID 

x.

Copy Configuration 
Image to Server

Specifies whether to copy the presently configured switch/stack parameters to 
the specified TFTP server (default is No).

Use the spacebar to toggle the selection to Yes.

Press 

Enter

 to initiate the process.

Default Value

No

Range

Yes, No

Retrieve Configuration 
Image from Server

Specifies whether to retrieve the stored switch/stack configuration parameters 
from the specified TFTP server (default is No). If you choose Yes, the 
download process begins immediately and, when completed, causes the 
switch/stack to reset with the new configuration parameters.

Use the spacebar to toggle the selection to Yes.

Press 

Enter

 to initiate the process.

Default Value

No

Range

Yes, No

Table 54   

Configuration File Download/Upload screen fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов