Nortel 425-24T Скачать руководство пользователя страница 333

Страница: 333 / 488

Chapter 8 Ethernet port management using the CLI

333

System Configuration Guide

Table 120

describes the parameters and variables for the

show

auto-negotiation-capabilities

command.

Figure 127

displays sample output from the

show

auto-negotiation-capabilities

command.

Figure 127

show auto-negotiation-capabilities command output

auto-negotiation-advertisements command

The

auto-negotiation-advertisements

command configures

advertisements for the switch. The syntax for the

auto-negotiation-advertisements

command is:

auto-negotiation-advertisements [port <portlist>] [10-full]

[10-half] [100-full] [100-half] [1000-full] [1000-half]

[asymm-pause-frame] [pause-frame] [none]

The

auto-negotiation-advertisements

command is in the interface

configuration command mode.

Table 120

show auto-negotiation-capabilities command

Parameters and values

Description

port <portlist>

Enter ports for which you want the autonegotiation
capabilities displayed.

425-48T(config-if)#show auto-negotiation-capabilities port 5,6,10

Port Autonegotiation Capabilities

---- ----------------------------------------------------------------

5 10Full 10Half 100Full 100Half

6 10Full 10Half 100Full 100Half

10 10Full 10Half 100Full 100Half

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 333 / 488

Результаты поиска

Содержание 425-24T

Отзывы: