manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 282 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 282

282

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

The 

no banner

 command is in the config mode.

Displaying the ARP table

The

 show arp-table 

command displays the arp table of the device. The 

syntax for the

 show arp-table 

command is:

show arp-table

The

 show arp-table

 

command is in the exec command mode. 

The

 show arp-table

 

command has no parameters or variables. 

Figure 103

 displays a sample output of the

 show arp-table 

command.

Figure 103   

show arp-table command output

Displaying interfaces

You can view the status of all interfaces on the switch or stack, including 
MultiLink Trunk membership, link status, autonegotiation, and speed. This 
section covers:

•

“show interfaces command”

•

“show interfaces config command”

425-48T#show arp-table

Port IP Address      MAC Address

---- --------------- -----------------

37   192.168.151.1   00:80:2D:6E:47:82

425-48T#

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов