Nortel 425-24T Скачать руководство пользователя страница 283

Страница: 283 / 488

Chapter 7 System configuration using the CLI

283

System Configuration Guide

show interfaces command

The

show interfaces

command displays the current configuration and status

of all interfaces. The syntax for the

show interfaces

command is:

show interfaces [names] [<portlist>]

The

show interfaces

command is in the exec command mode.

Table 83

describes the parameters and variables for the

show interfaces

command.

Figure 104

displays a sample output of the

show interfaces names

command.

Figure 104

show interfaces names command output

Figure 105

Shows a sample output of the

show interfaces

command without

the names variable.

Table 83

show interfaces command parameters and variables

Parameters and
variables

Description

names <portlist>

Displays the interface names; enter specific ports if you want to
see only those.

425_48T SW 1.1 in SC2-02 LAB>show interfaces names 1-3

Port Name

---- ----------------------------------------------------------------

LabBldg4

Testing

3 Floor1Bldg2

425_48T#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 283 / 488

Результаты поиска

Содержание 425-24T

Отзывы: